Models Showcase: free 3D-printable organizers

By Krypto

Complexity

Simple

Kitchen Coffee & tea

0

MAIN PURPOSE: Hang a cold brew bag in a jar

Rest the bridge on the mouth of a wide jar and hang a cold brew coffee or tea filter bag from the bar by its drawstring: the bag stays submerged without sinking to the bottom or flopping against the glass, and next morning you lift bridge and bag out together to drip over the sink.

Printing notes

24.5 cm³

Volume

30.4 g

Est. weight

1,648

Triangles

Food-safe PETG. Prints as shown on its floor, no supports.

AR view Open in app

By Krypto

Complexity

Simple

Kitchen Baking & sweets

0

Layer Lift

MAIN PURPOSE: Move whole cake layers without breaking them

A 200 mm flat lifter for moving whole sponge layers, cheesecakes and tart bases: slide it under the cake from the side, carry it on the broad blade and slide it off onto the stand or the next layer without cracking it. It doubles as a lid when you chill a layer.

Printing notes

125.7 cm³

Volume

155.9 g

Est. weight

1,576

Triangles

Food-safe PETG, printed flat; hand wash. Prints flat as a plate, no supports.

AR view Open in app

By Krypto

Complexity

Simple (set)

Kitchen Baking & sweets

0

Icing Corner

MAIN PURPOSE: Hold gingerbread walls square while icing sets

Gingerbread walls never stand up while the icing sets. Put one corner inside each corner of the house, press the two iced walls against its outer faces and they stay square and upright for the twenty minutes the royal icing needs. Print four, one per corner, and lift them out before the roof goes on.

Printing notes

26.4 cm³

Volume

32.7 g

Est. weight

72

Triangles

Food-safe PETG; print four. Prints as shown on its floor, no supports.

AR view Open in app

By Krypto

Complexity

Simple

Kitchen Kitchen organisers

0

Towel Shackle

MAIN PURPOSE: Keep a tea towel on the oven door

Snap the ring over the oven door bar and push a corner of the tea towel up through the slit into the round eye: the towel hangs where you need it, cannot slide off the bar onto the floor, and pulls free with one tug.

Printing notes

21.3 cm³

Volume

26.4 g

Est. weight

1,276

Triangles

Print it lying on its side (the profile flat on the bed) in PETG.

AR view Open in app

By Krypto

Complexity

Simple

Kitchen Food preparation

0

Scrap Gutter

MAIN PURPOSE: Sweep peelings off the board into a bin

Stand it against the side of the chopping board with the low back wall touching the board: peelings and trimmings sweep straight off the board over the scooped 22 mm lip and into the gutter, and the tall front keeps them in. Empty it into the compost in one tip.

Printing notes

39.6 cm³

Volume

49.1 g

Est. weight

1,724

Triangles

Food-safe PETG. Prints as shown on its floor, no supports.

AR view Open in app

By Krypto

Complexity

Simple

Others Home hardware & architecture

0

Exit Pocket

MAIN PURPOSE: Remember what to take when you leave

A pocket that hangs on the inside handle of the front door: slip the big hole in the back plate over the lever and drop in whatever must leave the house tomorrow, the letter to post, the parcel return label, the library card, the folded tote bag. You cannot open the door without touching it, so nothing is forgotten.

Printing notes

7.5 cm³

Volume

9.3 g

Est. weight

1,980

Triangles

PLA or PETG, printed upright. Prints as shown on its floor, no supports. Large holes in the walls may need supports or good bridging.

AR view Open in app

By Krypto

Complexity

Simple

Others Drawer & cabinet organisers

0

Stemline

MAIN PURPOSE: Hang wine glasses under a shelf

Screw it under a kitchen shelf or wall cupboard and slide wine glasses in by their feet: they hang upside down in a row, dust-free and out of the cupboard, which frees a whole shelf. Each 250 mm rail holds four glasses with feet up to 85 mm.

Printing notes

55.4 cm³

Volume

68.7 g

Est. weight

612

Triangles

PETG; print with support under the two ledges. Prints as shown on its floor, no supports.

AR view Open in app

By Krypto

Complexity

Simple (set)

Others Home hardware & architecture

0

Gallery Cross

MAIN PURPOSE: Space a grid of picture frames evenly

Hanging a grid of frames: hold the cross where four frame corners meet and butt each frame against its arms. The 50 mm arms set the gap between frames both ways at once, so a gallery wall of six or nine pictures comes out evenly spaced and square without measuring every gap.

Printing notes

67.5 cm³

Volume

83.7 g

Est. weight

2,680

Triangles

PLA, printed flat; print two for big walls. Prints flat as a plate, no supports.

AR view Open in app

By Krypto

Complexity

Simple

Others Travel & everyday carry

0

Table Perch

MAIN PURPOSE: Hang a bag under a cafe table

Rest the pad on a café or restaurant table so the hook hangs over the edge: the J curls back under the table top, so a handbag or laptop bag hangs off the floor, out of the aisle and against your knees where nobody can lift it. Flat enough for a coat pocket.

Printing notes

40.3 cm³

Volume

49.9 g

Est. weight

584

Triangles

Print it lying on its side (the profile flat on the bed) in PETG. Stick a felt pad under the top.

AR view Open in app

By Krypto

Complexity

Simple

Others Travel & everyday carry

0

Haul Hook

MAIN PURPOSE: Carry several shopping bags comfortably

Slip the handles of three or four shopping bags into the hook and carry them all by the 90 mm grip bar: the weight spreads across your whole palm instead of cutting into your fingers, and the J keeps the handles together so the bags stop swinging apart. Lives in the car door pocket.

Printing notes

70.4 cm³

Volume

87.3 g

Est. weight

848

Triangles

Print it lying on its side (the profile flat on the bed) in PETG.

AR view Open in app