Models Showcase: free 3D-printable organizers

By Krypto

Complexity

Simple

Desk & office Cables & charging

0

MAIN PURPOSE: Cover a cable crossing the floor

A floor cable cover: lay it over a lead that has to cross a hallway or the gap from desk to wall, and the 12 x 9 mm channel underneath hides it while the shallow ramps stop feet, chair wheels and vacuum heads catching. Print as many 200 mm lengths as the run needs and butt them end to end.

Printing notes

116.9 cm³

Volume

144.9 g

Est. weight

272

Triangles

Print it lying on its flat underside, in PETG or TPU. Prints as shown on its outline, no supports.

AR view Open in app

By Krypto

Complexity

Medium

Desk & office Desk organisation

0

Pivot Drawer

MAIN PURPOSE: Add a swing-out drawer under any desk

A pencil tray that screws under the desk top through its corner post and swings out on that single screw: push it back and it disappears under the edge, pull the finger notch and pens, cables and the stapler swing out to you. The post is 2 mm taller than the walls so the rim never rubs the desk.

Printing notes

72.1 cm³

Volume

89.5 g

Est. weight

2,588

Triangles

Print in PETG; one 4.5 mm wood screw and a washer. Prints as shown on its floor, no supports.

AR view Open in app

By Krypto

Complexity

Simple

Desk & office Cables & charging

0

Loop Lock

MAIN PURPOSE: Shorten a cable that is too long

Shorten a charger or headphone cable that is too long without coiling it: fold a loop of the excess and press both strands into the two side slots, which run in opposite directions so the cable takes an S-turn and holds. No unplugging, no ties, and sliding it along sets the length.

Printing notes

5.4 cm³

Volume

6.7 g

Est. weight

1,524

Triangles

PETG or TPU, printed flat. Prints as shown on its outline, no supports.

AR view Open in app

By Krypto

Complexity

Simple

Desk & office Office tools

0

Nib Rest

MAIN PURPOSE: Rest an open fountain pen without rolling

A low rest for fountain pens and brushes: lay a pen across one of the two cradles and the nib stays off the desk and the barrel cannot roll, so an uncapped pen can wait between sentences. Small enough to sit beside the notebook all day.

Printing notes

16.8 cm³

Volume

20.8 g

Est. weight

432

Triangles

Print it lying on its side (the profile flat on the bed) in PETG.

AR view Open in app

By Krypto

Complexity

Simple

Kitchen Coffee & tea

0

Steep Cap

MAIN PURPOSE: Cover a steeping mug, then rest the bag

Lay it upside down on a mug while the tea steeps, with the tag string through the notch: the tea stays hot and the bag cannot sink out of reach. When it is ready, lift it off, turn it over and it becomes the saucer for the wet tea bag and the spoon.

Printing notes

18.7 cm³

Volume

23.2 g

Est. weight

1,736

Triangles

Food-safe PETG. Print floor-down as shown, then turn it over to use it.

AR view Open in app

By Krypto

Complexity

Simple

Kitchen Coffee & tea

0

Cold Hang

MAIN PURPOSE: Hang a cold brew bag in a jar

Rest the bridge on the mouth of a wide jar and hang a cold brew coffee or tea filter bag from the bar by its drawstring: the bag stays submerged without sinking to the bottom or flopping against the glass, and next morning you lift bridge and bag out together to drip over the sink.

Printing notes

24.5 cm³

Volume

30.4 g

Est. weight

1,648

Triangles

Food-safe PETG. Prints as shown on its floor, no supports.

AR view Open in app

By Krypto

Complexity

Multi-part assembly

Kitchen Food preparation

0

Emulsion Line

MAIN PURPOSE: Mix a perfect vinaigrette by the marks

A screw-top dressing shaker with the recipe on the side: pour vinegar or lemon juice up to the lower mark and oil up to the upper one, add salt and a spoon of mustard, screw on the lid and shake. The marks give the classic one-to-three vinaigrette every time, and the leftovers keep in the fridge in the same jar.

Printing notes

30.6 cm³

Volume

38.0 g

Est. weight

8,512

Triangles

Food-safe PETG, 3 walls so it is watertight. Prints as shown on its floor, no supports. The threaded lid and its neck piece print separately; adjust Fit in the Lid tab if it binds.

AR view Open in app

By Krypto

Complexity

Simple

Kitchen Baking & sweets

0

Layer Lift

MAIN PURPOSE: Move whole cake layers without breaking them

A 200 mm flat lifter for moving whole sponge layers, cheesecakes and tart bases: slide it under the cake from the side, carry it on the broad blade and slide it off onto the stand or the next layer without cracking it. It doubles as a lid when you chill a layer.

Printing notes

125.7 cm³

Volume

155.9 g

Est. weight

1,576

Triangles

Food-safe PETG, printed flat; hand wash. Prints flat as a plate, no supports.

AR view Open in app

By Krypto

Complexity

Simple (set)

Kitchen Baking & sweets

0

Icing Corner

MAIN PURPOSE: Hold gingerbread walls square while icing sets

Gingerbread walls never stand up while the icing sets. Put one corner inside each corner of the house, press the two iced walls against its outer faces and they stay square and upright for the twenty minutes the royal icing needs. Print four, one per corner, and lift them out before the roof goes on.

Printing notes

26.4 cm³

Volume

32.7 g

Est. weight

72

Triangles

Food-safe PETG; print four. Prints as shown on its floor, no supports.

AR view Open in app

By Krypto

Complexity

Medium

Kitchen Serving & table

0

Dip Palette

MAIN PURPOSE: Hold snacks and dips in one hand

A painter’s palette for the sofa or a standing party: put your thumb through the hole and you can hold crisps, crudités and two dips in one hand, leaving the other free for a drink. Two low walls split it into three wells so salsa, hummus and chips stay apart.

Printing notes

86.8 cm³

Volume

107.7 g

Est. weight

1,204

Triangles

Food-safe PETG. Prints as shown on its outline, no supports.

AR view Open in app