Models Showcase: free 3D-printable organizers

By Krypto

Complexity

Multi-part assembly

Health & medicine

0

First aid box

A two-bay first aid box with a bar-handled lid and FIRST AID on the front.

Printing notes

409.5 cm³

Volume

507.8 g

Est. weight

8,656

Triangles

Prints as shown on its floor, no supports. The added base's lid prints separately. Stacked parts are fused into one print.

AR view Open in app

Preview of Toilet cistern displacement box

By Krypto

Complexity

Multi-part assembly

Others Sustainable living

0

Toilet cistern displacement box

MAIN PURPOSE: Save water on every toilet flush

Stand it in the cistern clear of the float and the flush valve, fill it with water or gravel and close the snug lid: every flush now uses about a litre less, the job a brick used to do, but without crumbling grit into the valve.

Printing notes

42.0 cm³

Volume

52.1 g

Est. weight

7,120

Triangles

PETG with solid walls so it stays watertight. Prints as shown on its floor, no supports. The lid prints as a separate part, top down.

AR view Open in app

By Krypto

Complexity

Multi-part assembly

Others Home hardware & architecture

0

Pendant flex shortener

MAIN PURPOSE: Shorten a hanging lamp cable neatly

Takes up spare pendant flex neatly instead of a knot: feed the sheathed cable in one side, wind the slack round the inner ring, out of the other side and close the lid. The lamp hangs at exactly the height you want.

Printing notes

36.5 cm³

Volume

45.3 g

Est. weight

6,560

Triangles

Only for sheathed flex, never bare wires. Prints as shown on its floor, no supports. The lid prints as a separate part, top down.

AR view Open in app

By Krypto

Complexity

Multi-part assembly

Others Drawer & cabinet organisers

0

Bin liner roll dispenser

MAIN PURPOSE: Dispense bin liners one at a time

Screw it inside the bin cupboard door, drop in a roll of bin liners and pull the first through the slot: each bag tears off with the next one waiting in the slot, so the roll never unravels in the back of a drawer.

Printing notes

137.5 cm³

Volume

170.5 g

Est. weight

6,072

Triangles

Prints as shown on its floor, no supports. The lid prints as a separate part, top down.

AR view Open in app

By Krypto

Complexity

Multi-part assembly

Others Garden & plants

0

Mason bee cocoon release box

MAIN PURPOSE: Release mason bee cocoons safely in spring

Put cleaned mason bee cocoons in the box in spring and hang it beside the bee hotel: the bees chew out and leave through the single 8 mm hole, while birds and mice cannot reach the cocoons and the lid lifts off to clear the empty cases.

Printing notes

50.3 cm³

Volume

62.3 g

Est. weight

13,656

Triangles

Prints as shown on its floor, no supports. The lid prints as a separate part, top down.

AR view Open in app

By Krypto

Complexity

Multi-part assembly

Others Health & medicine

0

Used test strip pocket bin

MAIN PURPOSE: Collect used glucose test strips on the go

A screw-top canister with a slot in the lid: drop each used glucose test strip straight in at the table or on the go instead of leaving them in the meter case. Not a sharps container: used lancets still go in a proper sharps bin.

Printing notes

14.8 cm³

Volume

18.3 g

Est. weight

7,440

Triangles

Prints as shown on its floor, no supports. The threaded lid and its neck piece print separately; adjust Fit in the Lid tab if it binds.

AR view Open in app

By Krypto

Complexity

Multi-part assembly

Workshop Finishing & painting

0

Knife-edge spray turntable

MAIN PURPOSE: Spray parts all round without touching them

Parts sit on eight thin ribs instead of a flat floor, so overspray never glues them down and their undersides stay clean; the base spins on BBs, so you turn the part while spraying instead of walking round it.

Printing notes

332.8 cm³

Volume

412.6 g

Est. weight

6,944

Triangles

Prints as shown on its floor, no supports. The turntable ring prints separately and runs on 6 mm BBs.

AR view Open in app

By Krypto

Complexity

Multi-part assembly

Workshop Workshop storage

0

Respirator cartridge keeper

MAIN PURPOSE: Seal a respirator away from dust and fumes

Organic vapour cartridges keep soaking up fumes and dust whenever they sit in open air. Seal the half mask and its cartridges in this snug box between jobs and they last many times longer, and the face seal stays clean and undistorted.

Printing notes

114.6 cm³

Volume

142.1 g

Est. weight

10,648

Triangles

Prints as shown on its floor, no supports. The lid prints as a separate part, top down.

AR view Open in app

By Krypto

Complexity

Multi-part assembly

Others Sport & fitness

0

Rotating push-up handle

MAIN PURPOSE: Let wrists rotate naturally during push-ups

The grip beam sits on two posts above a lazy-Susan base, so the handle turns freely as you lower and press: wrists and elbows follow their natural rotation instead of being locked straight, which takes the strain off sore joints. Print two.

Printing notes

179.0 cm³

Volume

221.9 g

Est. weight

9,048

Triangles

PETG; load the base with 6 mm BBs. Print two. Prints as shown on its floor, no supports. The turntable ring prints separately and runs on 6 mm BBs. Stacked parts are fused into one print.

AR view Open in app

By Krypto

Complexity

Multi-part assembly

Others Photography & film

0

Product photo 360 turntable

MAIN PURPOSE: Shoot evenly spaced 360 degree product photos

A lazy-Susan turntable with 0 to 315 degree marks engraved round the lid: turn the product one mark per shot and you get eight evenly spaced frames for a 360 degree spin on a web shop, with no motor and no guesswork.

Printing notes

477.2 cm³

Volume

591.7 g

Est. weight

25,548

Triangles

Load the base with 6 mm BBs. Prints as shown on its floor, no supports. The lid prints as a separate part, top down. The turntable ring prints separately and runs on 6 mm BBs.

AR view Open in app