Showcase

Models Showcase

Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category

All Kitchen Desk & office Workshop Bedroom & bathroom Others
Preview of Submarine bath-tea infuser
By Krypto
Complexity
Multi-part assembly
Bedroom & bathroom Bath & body care
0
Submarine bath-tea infuser
MAIN PURPOSE: Hang a pierced submarine of bath herbs under the hot tap
Bath tea is a pot of herbs for the bath, and this one is a little submarine. Fill the hull with oats, lavender, rose petals or chamomile, close the hatch and hang it by the ring on its conning tower under the hot tap: the water pours in through the hatch rim and out through the eight holes in the hull, smelling of the herbs, without a single petal in the bath. When the bath is full, unhook it and let it dive to the bottom to keep steeping.
Printing notes
100.5 cm³
Volume
124.6 g
Est. weight
4,360
Triangles

PETG. Fill with oats, lavender, chamomile or rose petals; hang it from the tap by the ring on its tower while the bath runs. Prints as shown on its floor, no supports. The friction-fit lid and its neck piece print separately; adjust Fit in the Lid tab if it binds.

AR view Open in app
Preview of Ocean-wave drum
By Krypto
Complexity
Multi-part assembly
Others Music & audio
0
Ocean-wave drum
MAIN PURPOSE: Tilt a sealed drum of beads slowly to hear surf breaking on a beach
Ocean drums are an old sound-effects trick, used in theatres and music therapy. A handful of steel beads lies inside a wide, flat drum. Tilt it slowly and the beads roll across the wave-ridged floor in a long rushing hiss, exactly like a wave running up the sand; tip it back and the wave draws away. Shake it for rain, roll it for a storm. Children love it, and it is wonderfully calming at bedtime.
Printing notes
233.9 cm³
Volume
290.1 g
Est. weight
4,900
Triangles

Fill with a handful of 4.5 mm steel BBs (or dry lentils for a softer sound), then screw the lid on. Prints as shown on its floor, no supports. The threaded lid and its neck piece print separately; adjust Fit in the Lid tab if it binds.

AR view Open in app
Preview of Spin-dial dog treat puzzle
By Krypto
Complexity
Medium
Others Pets & aquarium
0
Spin-dial dog treat puzzle
MAIN PURPOSE: Hide treats in eight bays under a dial the dog noses round to find them
A brain game for dogs. Drop a treat into each of the eight bays and put the dial on top: it has a single window, so only one bay is open at a time. The dog has to work out that nudging the dial round with nose or paw reveals the next treat. Ten minutes of sniffing and thinking tires a dog out more than a long walk. Leave some bays empty to make it harder.
Printing notes
272.0 cm³
Volume
337.2 g
Est. weight
3,636
Triangles

PETG. Let the dog watch you load it the first few times; supervise and put it away after play. Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Gummy-bear osmosis lab
By Krypto
Complexity
Medium
Others Science & education
0
Gummy-bear osmosis lab
MAIN PURPOSE: Watch gummy bears grow, shrink or dissolve in four liquids overnight
Put one gummy bear on the millimetre grid in each bay and measure it, then cover them with plain water, salty water, sugary water and vinegar. By morning the water bear has swollen to twice its size as water rushes in through its skin by osmosis, the salty and sugary ones barely change, and the vinegar bear has started to dissolve. Measure them on the grid again and record the results. A classic science experiment in a neat tray.
Printing notes
59.9 cm³
Volume
74.3 g
Est. weight
15,068
Triangles

Print in white so the grid shows. Use 50 ml of liquid per bay and the same brand of bear in each. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Scrap-regrow windowsill station
By Krypto
Complexity
Advanced
Kitchen Sustainable living
0
Scrap-regrow windowsill station
MAIN PURPOSE: Regrow lettuce, celery, spring onions and carrot tops from kitchen scraps
The root ends you throw away will grow again. Stand a lettuce or bok choy stump in the wide dish, a celery base in the shallow one, the white roots of spring onions upright in the tall tube and carrot tops in the small cup, each in a little water. Within days new leaves push up from the middle: spring onions can be cut again in a week, celery grows a new heart and carrot tops sprout feathery greens for pesto. Each well is labelled in its floor.
Printing notes
110.4 cm³
Volume
136.9 g
Est. weight
13,256
Triangles

PETG. Use 1-2 cm of water and change it every two days; keep it on a bright windowsill. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Shower-thoughts idea pod
By Krypto
Complexity
Medium
Bedroom & bathroom Bath & body care
0
Shower-thoughts idea pod
MAIN PURPOSE: Catch the ideas you have in the shower on a waterproof pad before they vanish
Your best ideas arrive in the shower, and are gone by the time you are dry. This wall pod holds a waterproof notepad behind a big window you can write through, a pencil in its own tube, and drain holes so nothing pools. Write the idea down mid-rinse, tear off the sheet later. SHOWER THOUGHTS is raised above the window.
Printing notes
45.8 cm³
Volume
56.8 g
Est. weight
13,216
Triangles

PETG. Fits a waterproof A6 notepad (or a slate of white plastic and a grease pencil). Screw it up through the keyholes. Prints as shown on its floor, no supports. Large holes in the walls may need supports or good bridging.

AR view Open in app
Preview of Round two-tier screw-together stand
By Krypto
Complexity
Medium
Kitchen Serving & table
0
Round two-tier screw-together stand
MAIN PURPOSE: Serve sweets, fruit or trinkets on two round tiers that screw together
A two-tier stand of round trays, 150 and 130 mm across, the top one held 30 mm above the bottom one on a slim screw-in column, on a single round pedestal with a wide foot. It comes apart flat for storage, and every part prints on its own without supports.
Printing notes
141.4 cm³
Volume
175.4 g
Est. weight
6,596
Triangles

Every part prints flat with no supports. Screw the column onto the stud in the bottom tray, screw the top tray on, and push the pedestal peg up into the bottom tray. Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Round pedestal tray
By Krypto
Complexity
Simple
Kitchen Serving & table
0
Round pedestal tray
MAIN PURPOSE: Raise a round tray on a single pedestal for display or serving
A 150 mm round tray lifted 45 mm off the table on a single round pedestal with a wide foot, like a small cake stand. The pedestal pushes into the tray on a press-fit peg, so both parts print flat without supports.
Printing notes
85.8 cm³
Volume
106.3 g
Est. weight
1,232
Triangles

Both parts print flat with no supports. Push the pedestal peg up into the hole in the tray; a drop of glue makes it permanent. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Square two-tier screw-together stand
By Krypto
Complexity
Medium
Kitchen Serving & table
0
Square two-tier screw-together stand
MAIN PURPOSE: Serve sweets, fruit or trinkets on two square tiers that screw together
A two-tier stand of square, round-cornered trays, 150 and 130 mm across, the top one held 30 mm above the bottom one on a slim screw-in column, on a single square pedestal with a wide foot. It comes apart flat for storage, and every part prints on its own without supports.
Printing notes
128.6 cm³
Volume
159.5 g
Est. weight
6,436
Triangles

Every part prints flat with no supports. Screw the column onto the stud in the bottom tray, screw the top tray on, and push the pedestal peg up into the bottom tray. Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Square pedestal tray
By Krypto
Complexity
Simple
Kitchen Serving & table
0
Square pedestal tray
MAIN PURPOSE: Raise a square tray on a single pedestal for display or serving
A 150 mm square, round-cornered tray lifted 45 mm off the table on a single square pedestal with a wide foot, like a small cake stand. The pedestal pushes into the tray on a press-fit peg, so both parts print flat without supports.
Printing notes
82.9 cm³
Volume
102.8 g
Est. weight
1,376
Triangles

Both parts print flat with no supports. Push the pedestal peg up into the hole in the tray; a drop of glue makes it permanent. Prints as shown on its floor, no supports.

AR view Open in app

SO3D.xyz is free and built by one maker. Help keep it running.

Be one of the first supporters this month.
Support · Buy me a coffeeSee the Hobbyist plan