Showcase

Models Showcase

Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category

All Kitchen Desk & office Workshop Bedroom & bathroom Others
Preview of Shampoo-bar travel tin with raised ledge
By Krypto
Complexity
Multi-part assembly
Bath & body care
0
Shampoo-bar travel tin with raised ledge
MAIN PURPOSE: Carry a shampoo bar without it going soggy
A travel tin for a solid shampoo or soap bar. A ledge round the inside holds the bar up off the floor so it can drain and dry, and drain holes let the water out. The lid keeps it in your bag.
Printing notes
104.0 cm³
Volume
128.9 g
Est. weight
2,368
Triangles

Leave the lid off overnight so the bar dries hard. Prints as shown on its floor, no supports. The friction-fit lid and its neck piece print separately; adjust Fit in the Lid tab if it binds.

AR view Open in app
Preview of Honeycomb-drain pedestal soap dish
By Krypto
Complexity
Medium
Bath & body care
0
Honeycomb-drain pedestal soap dish
MAIN PURPOSE: Keep a bar of soap dry on the basin
A raised round soap dish with a honeycomb cut straight through the floor, so water drains away and the soap dries on its pedestal.
Printing notes
56.1 cm³
Volume
69.6 g
Est. weight
5,966
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Low-poly faceted toothbrush cup
By Krypto
Complexity
Medium
Bath & body care
0
Low-poly faceted toothbrush cup
MAIN PURPOSE: Hold toothbrushes by the basin
A faceted cup for toothbrushes and toothpaste, with a geometric low-poly surface.
Printing notes
101.4 cm³
Volume
125.8 g
Est. weight
1,088
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Submarine bath-tea infuser
By Krypto
Complexity
Multi-part assembly
Bedroom & bathroom Bath & body care
0
Submarine bath-tea infuser
MAIN PURPOSE: Hang a pierced submarine of bath herbs under the hot tap
Bath tea is a pot of herbs for the bath, and this one is a little submarine. Fill the hull with oats, lavender, rose petals or chamomile, close the hatch and hang it by the ring on its conning tower under the hot tap: the water pours in through the hatch rim and out through the eight holes in the hull, smelling of the herbs, without a single petal in the bath. When the bath is full, unhook it and let it dive to the bottom to keep steeping.
Printing notes
100.5 cm³
Volume
124.6 g
Est. weight
4,360
Triangles

PETG. Fill with oats, lavender, chamomile or rose petals; hang it from the tap by the ring on its tower while the bath runs. Prints as shown on its floor, no supports. The friction-fit lid and its neck piece print separately; adjust Fit in the Lid tab if it binds.

AR view Open in app
Preview of Shower-thoughts idea pod
By Krypto
Complexity
Medium
Bedroom & bathroom Bath & body care
0
Shower-thoughts idea pod
MAIN PURPOSE: Catch the ideas you have in the shower on a waterproof pad before they vanish
Your best ideas arrive in the shower, and are gone by the time you are dry. This wall pod holds a waterproof notepad behind a big window you can write through, a pencil in its own tube, and drain holes so nothing pools. Write the idea down mid-rinse, tear off the sheet later. SHOWER THOUGHTS is raised above the window.
Printing notes
45.8 cm³
Volume
56.8 g
Est. weight
13,216
Triangles

PETG. Fits a waterproof A6 notepad (or a slate of white plastic and a grease pencil). Screw it up through the keyholes. Prints as shown on its floor, no supports. Large holes in the walls may need supports or good bridging.

AR view Open in app
Preview of Shower squeegee holster
By Krypto
Complexity
Medium
Bedroom & bathroom Bath & body care
0
Shower squeegee holster
MAIN PURPOSE: Hang a shower squeegee blade-down to drip dry
A holster that keeps the shower squeegee within reach. The blade drops in edge-down, water drains straight out through the slotted floor, and keyholes hang it on the tiles. It is the one-minute habit that saves scrubbing limescale later.
Printing notes
17.1 cm³
Volume
21.2 g
Est. weight
9,224
Triangles

Mount with keyholes on screws or stick-on hooks; the slotted floor drains. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Drip Tip
By Krypto
Complexity
Medium
Bedroom & bathroom Bath & body care
0
Drip Tip
MAIN PURPOSE: Keep a soap bar dry and drain it off a leaf tip
A soap dish drawn from a rainforest leaf. Rainforest leaves end in a long drip tip that sheds water so the blade dries fast; here three short cross veins lift the bar off the floor, water runs round them into the narrow tip and drips out of the hole at its end. Set it on the basin rim with the tip over the bowl.
Printing notes
23.1 cm³
Volume
28.6 g
Est. weight
1,124
Triangles

PETG. Print flat.

AR view Open in app
Preview of Shower leg-shaving foot rest
By Krypto
Complexity
Simple
Bedroom & bathroom Bath & body care
0
Shower leg-shaving foot rest
MAIN PURPOSE: Raise a foot safely for shaving in the shower
Stand it on the shower floor against the wall and put one foot on the 15 degree tread: the leg is raised and bent for shaving or washing without balancing on one foot on a wet floor. The trussed profile carries full body weight.
Printing notes
407.6 cm³
Volume
505.5 g
Est. weight
764
Triangles

Print as it comes (profile on the bed) in PETG, 40% infill.

AR view Open in app
Preview of Magnetic under-shelf soap mount
By Krypto
Complexity
Simple
Bedroom & bathroom Bath & body care
0
Magnetic under-shelf soap mount
MAIN PURPOSE: Hang a bar of soap on a magnet to dry
Screw the cup under a shelf or the shower caddy, press a 20 x 3 mm magnet into it, and push a steel bottle cap into the back of the soap bar: the soap hangs in the air, dries all round and never sits in a slimy dish again.
Printing notes
2.5 cm³
Volume
3.1 g
Est. weight
848
Triangles

Add a 20 x 3 mm magnet and a steel bottle cap. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Toilet seat lifting tab
By Krypto
Complexity
Simple
Bedroom & bathroom Bath & body care
0
Toilet seat lifting tab
MAIN PURPOSE: Lift the toilet seat without touching it
Stick the pad to the underside of the toilet seat near the front: the angled tab gives a finger something to lift, so nobody grabs the rim of the seat itself. Small, discreet and easy to wipe.
Printing notes
11.5 cm³
Volume
14.3 g
Est. weight
408
Triangles

Print as it comes (profile on the bed) in PETG; fix with waterproof tape.

AR view Open in app

SO3D.xyz is free and built by one maker. Help keep it running.

Be one of the first supporters this month.
Support · Buy me a coffeeSee the Hobbyist plan