Showcase

Models Showcase

Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category

All Kitchen Desk & office Workshop Bedroom & bathroom Others
Preview of Powder pan re-pressing tamper
By Krypto
Complexity
Advanced
Bedroom & bathroom Makeup & beauty
0
Powder pan re-pressing tamper
MAIN PURPOSE: Repair broken pressed powder makeup
Crush a broken eyeshadow or blusher, wet it with a few drops of surgical spirit, cover with kitchen paper and press with this 25 mm tamper: the powder sets into a smooth, solid cake again instead of being thrown away.
Printing notes
8.2 cm³
Volume
10.2 g
Est. weight
2,200
Triangles

Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Fingertip rest for drying nail polish
By Krypto
Complexity
Advanced
Bedroom & bathroom Makeup & beauty
0
Fingertip rest for drying nail polish
MAIN PURPOSE: Let painted nails dry without smudges
Rest the palm in the tray and the fingertips on the five posts: the pads of the fingers take the weight and the wet nails float in the air, so a fresh manicure dries without a single smudge.
Printing notes
57.6 cm³
Volume
71.5 g
Est. weight
5,204
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Aligner soak basket with lift tab
By Krypto
Complexity
Advanced
Bedroom & bathroom Bath & body care
0
Aligner soak basket with lift tab
MAIN PURPOSE: Soak aligners and lift them out hands-free
Put aligners, a retainer or a night guard in the slotted basket and stand it in a tumbler of cleaning solution: afterwards lift it out by the tall tab and rinse it under the tap, without dipping fingers in the solution.
Printing notes
6.3 cm³
Volume
7.8 g
Est. weight
13,110
Triangles

Fits a tumbler 80 mm or wider. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Heat-set insert plumb bridge
By Krypto
Complexity
Advanced
Workshop Maker & 3D printing
0
Heat-set insert plumb bridge
MAIN PURPOSE: Press heat-set inserts in square
Slide the printed part under the bridge with its hole below the bore and lower the soldering iron through the 11 mm guide tube: the iron can only travel straight down, so threaded heat-set inserts go in square instead of tilting and leaving a crooked M3 thread.
Printing notes
25.6 cm³
Volume
31.7 g
Est. weight
944
Triangles

Print in PETG or ASA; the iron barrel should not touch the bore for long. Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Ribbed lightweight plasterer's hawk
By Krypto
Complexity
Advanced
Workshop Trade & professional tools
0
Ribbed lightweight plasterer's hawk
MAIN PURPOSE: Carry plaster or mortar on a light hawk
A 250 mm hawk printed face down: the flat face carries the plaster, a grid of ribs underneath keeps it stiff and light, and the 40 mm handle stands on the centre cross. Easy to wash, and it never warps after a soaking the way plywood hawks do.
Printing notes
265.7 cm³
Volume
329.5 g
Est. weight
1,744
Triangles

Needs a 250 mm bed; print in PETG. Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Honing guide projection jig
By Krypto
Complexity
Advanced
Workshop Woodworking
0
Honing guide projection jig
MAIN PURPOSE: Set honing guide projection repeatably
Hook a side-clamp honing guide over the low front wall and slide the blade forward until it touches a stop block: the four stepped blocks set 32, 38, 42 and 50 mm of projection, the settings for 25 and 30 degree bevels on plane irons and chisels in an Eclipse-pattern guide. Every resharpening lands on the same angle.
Printing notes
47.1 cm³
Volume
58.4 g
Est. weight
15,288
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Self-centring dowelling jig for 18 mm board
By Krypto
Complexity
Advanced
Workshop Tools & jigs
0
Self-centring dowelling jig for 18 mm board
MAIN PURPOSE: Drill centred dowel holes in board edges
Drop the jig over the edge of 18 mm board: the two fences straddle it, so the guide holes sit dead centre on the edge, 32 mm apart, and the double guide plates keep an 8 mm bit square. Drill both parts from their face side and the dowels line up every time. Print it as shown, then turn it over so the floor becomes the top.
Printing notes
9.5 cm³
Volume
11.7 g
Est. weight
1,008
Triangles

Print in PETG with 100% infill round the holes. Print floor-down as shown, then turn it over to use it.

AR view Open in app
Preview of Hand tap square-start guide
By Krypto
Complexity
Advanced
Workshop Tools & jigs
0
Hand tap square-start guide
MAIN PURPOSE: Start hand taps square to the work
Clamp or hold the block over a drilled hole and start the tap through the matching guide: two plates 30 mm apart keep an M3, M4, M5 or M6 tap square to the work for the first turns, the moment where most crooked threads and snapped taps happen.
Printing notes
11.5 cm³
Volume
14.3 g
Est. weight
7,836
Triangles

Print in PETG. Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Square-head bench dogs
By Krypto
Complexity
Advanced (set)
Workshop Tools & jigs
0
Square-head bench dogs
MAIN PURPOSE: Fence and square work on a dog-hole bench
A 19 mm peg for 20 mm dog holes with a square head whose four flat faces each sit exactly 20 mm from the peg centre: two dogs make a fence parallel to the hole grid, three make a square corner, and the flat faces spread the pressure instead of denting edges like round dogs.
Printing notes
17.0 cm³
Volume
21.1 g
Est. weight
800
Triangles

Print three, with supports under the head. Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of 608 bearing press-in driver
By Krypto
Complexity
Advanced
Workshop Tools & jigs
0
608 bearing press-in driver
MAIN PURPOSE: Press bearings in without damaging them
Presses a 608 skateboard bearing into a hub or housing by its outer race only: the narrow 1.5 mm rim bears on the race while the 19 mm opening clears the shield and inner race. Tap the solid end with a mallet and the bearing goes in square without brinelling its balls.
Printing notes
19.6 cm³
Volume
24.3 g
Est. weight
1,520
Triangles

Print in PETG with 100% infill. Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app

SO3D.xyz is free and built by one maker. Help keep it running.

Be one of the first supporters this month.
Support · Buy me a coffeeSee the Hobbyist plan