Models Showcase: free 3D-printable organizers

By Krypto

Complexity

Simple

Others Travel & everyday carry

0

MAIN PURPOSE: Hold a phone or list on a shopping trolley

Snap it onto the handle of a supermarket trolley or basket and stand your phone or paper shopping list in the fork: the list stays in front of you at eye level and both hands stay free for the shelves. Fits handles 28 to 32 mm and phones up to 15 mm thick in a case.

Printing notes

37.0 cm³

Volume

45.9 g

Est. weight

872

Triangles

Print it lying on its side (the profile flat on the bed) in PETG.

AR view Open in app

By Krypto

Complexity

Multi-part assembly

Others Travel & everyday carry

0

Twin Landing

MAIN PURPOSE: Pack small valuables, then tray them out

Packs as one closed box for watch, rings, earbuds and cables; in the hotel room lift off the lid, set it down beside the base and you have two landing trays on the nightstand, one for what comes out of your pockets and one for what goes back in tomorrow.

Printing notes

91.5 cm³

Volume

113.4 g

Est. weight

8,572

Triangles

PLA or PETG; line the trays with felt. Prints as shown on its floor, no supports. The lid prints as a separate part, top down.

AR view Open in app

By Krypto

Complexity

Simple

Others Travel & everyday carry

0

Tap Sleeve

MAIN PURPOSE: Tap a transit card without taking it out

Slide the sleeve onto the shoulder strap of your backpack and push your transit or office pass into the front channel: at the ticket gate or door reader you tap your shoulder, through the 46 mm window, instead of digging through pockets. The card cannot slip out sideways and the strap slides in through the side gap.

Printing notes

29.0 cm³

Volume

35.9 g

Est. weight

1,044

Triangles

PETG, printed standing on end so the channel is clean.

AR view Open in app

By Krypto

Complexity

Simple

Others Travel & everyday carry

0

Sleeper Ledge

MAIN PURPOSE: Add a bedside shelf to a bunk or berth

Hook it over the guard rail of a bunk, sleeper train berth or hostel bed: the 70 mm shelf sits on the mattress side at pillow height and holds phone, glasses and earplugs within reach in the dark, instead of lost in the sheets. Fits rails up to 26 mm thick.

Printing notes

128.8 cm³

Volume

159.7 g

Est. weight

472

Triangles

Print it lying on its side (the profile flat on the bed) in PETG.

AR view Open in app

By Krypto

Complexity

Simple

Others Travel & everyday carry

0

Cuff Handle

MAIN PURPOSE: Add a handle to a takeaway coffee cup

Slide the split ring up a paper takeaway cup until it wedges on the taper: the hot cup now has a proper handle, so you can carry it without a sleeve or burnt fingers, and it slips off and back into your bag when the cup goes in the recycling. Fits most 12 oz cups.

Printing notes

12.1 cm³

Volume

15.0 g

Est. weight

712

Triangles

PETG, printed flat. Prints flat as a plate, no supports.

AR view Open in app

By Krypto

Complexity

Simple

Workshop Tools & jigs

0

Pin Pilot

MAIN PURPOSE: Start small nails without hitting fingers

Press a panel pin or small nail into the slot that grips it and tap it in while holding the long handle: your fingers stay 100 mm from the hammer, and the three slots take shanks from 1.4 to 3 mm. Pull the holder away sideways once the nail stands on its own.

Printing notes

9.7 cm³

Volume

12.0 g

Est. weight

308

Triangles

PETG, printed flat. Prints flat as a plate, no supports.

AR view Open in app

By Krypto

Complexity

Medium

Workshop Tools & jigs

0

Arc Rider

MAIN PURPOSE: Turn a tape measure into a big compass

Slide the clip onto a tape measure blade and push a pencil through the side ring: hook the tape over a nail at the centre point, lock it at the radius you want and swing it, and the pencil draws circles and arcs as large as the tape is long, for arches, round tables and garden beds.

Printing notes

4.7 cm³

Volume

5.8 g

Est. weight

980

Triangles

PETG; check the grooves against your 25 mm blade. Prints as shown on its floor, no supports.

AR view Open in app

By Krypto

Complexity

Multi-part assembly

Workshop Finishing & painting

0

Mini Podium

MAIN PURPOSE: Grip a miniature and store its parts inside

A miniature painting handle with a storage chamber: fix the figure to the screw lid with a dab of putty and hold the 36 mm body like a thick pen, then unscrew it between figures to keep spare bases, magnets and a brush tip inside. It stands upright on its own while the paint dries.

Printing notes

23.5 cm³

Volume

29.2 g

Est. weight

2,324

Triangles

PLA or PETG; print the lid face down for a flat top. Prints as shown on its floor, no supports. The threaded lid and its neck piece print separately; adjust Fit in the Lid tab if it binds.

AR view Open in app

By Krypto

Complexity

Simple

Workshop Woodworking

0

Spoon Blank

MAIN PURPOSE: Mark out a carving spoon blank

Lay the template on a split green-wood blank with the notches on the grain line and draw round it: you get a well-proportioned eating spoon, a 46 mm bowl on a 190 mm handle, ready to axe and carve, and every spoon in a set comes out the same size.

Printing notes

13.9 cm³

Volume

17.3 g

Est. weight

2,604

Triangles

PLA, printed flat. Prints flat as a plate, no supports.

AR view Open in app

By Krypto

Complexity

Simple

Workshop Woodworking

0

Sheet Mule

MAIN PURPOSE: Carry big sheets of board single-handed

Carry a full sheet of plywood or plasterboard on your own: hook the bottom edge into the J, stand the sheet on edge against your side and lift by the top handle. Your arm hangs straight, the board stays vertical and the sheet no longer needs two people or a wide arm span.

Printing notes

200.0 cm³

Volume

248.0 g

Est. weight

904

Triangles

PETG at 100 % infill, printed on its side.

AR view Open in app