Showcase
Models Showcase
Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category
MAIN PURPOSE: Make yarn pom-poms
Print two of these C-rings and hold them together: wind yarn round and round, cut along the outer edge between the rings, tie the middle tightly and slide the rings off for a full, round pom-pom.
Printing notes
11.7 cm³
Volume
14.5 g
Est. weight
416
Triangles
Print two. Prints flat as a plate, no supports.
MAIN PURPOSE: Carry weft yarn through a loom
A flat stick shuttle for frame and rigid-heddle looms: wind the weft yarn lengthways between the U-notches at each end and pass it through the shed in one smooth slide.
Printing notes
16.7 cm³
Volume
20.7 g
Est. weight
192
Triangles
Prints flat as a plate, no supports.
MAIN PURPOSE: Wind and label embroidery thread
Wind a skein of embroidery thread onto the bobbin, tuck the end into the side slit and write the colour number on it; a set keeps a whole floss collection tangle-free.
Printing notes
3.8 cm³
Volume
4.7 g
Est. weight
296
Triangles
Print a set in one go. Prints flat as a plate, no supports.
MAIN PURPOSE: Keep candle wicks centred while pouring
Lay it across the jar while the wax sets: thread the wick through the centre hole, or two wicks through the outer holes, and they stay straight and centred.
Printing notes
6.4 cm³
Volume
7.9 g
Est. weight
1,156
Triangles
Prints flat as a plate, no supports.
MAIN PURPOSE: Catch and return embossing powder
Pour embossing powder or glitter over a stamped card held above the tray; the excess falls in, and the pouring notch in the low front wall funnels it straight back into the jar.
Printing notes
38.2 cm³
Volume
47.4 g
Est. weight
1,736
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Braid cord and bracelets
A disc for Japanese kumihimo braiding: hook eight or more threads into the 32 edge slits, rotate the disc and move the threads in turn, and the braid grows down through the centre hole.
Printing notes
83.0 cm³
Volume
102.9 g
Est. weight
912
Triangles
Print in TPU or PETG so the slits grip the threads. Prints flat as a plate, no supports.
MAIN PURPOSE: Support a guitar neck during maintenance
Supports a guitar neck while you restring, clean the fretboard or adjust the truss rod; stick felt or foam into the cradle so it never marks the finish.
Printing notes
92.0 cm³
Volume
114.1 g
Est. weight
1,032
Triangles
Print as it comes, side outline on the bed.
MAIN PURPOSE: Hang a bag or headset at a desk
Slides onto a desk or table top up to 25 mm thick and gives a hook at the edge for a handbag, a backpack or a headset, keeping them off the floor.
Printing notes
35.5 cm³
Volume
44.1 g
Est. weight
624
Triangles
Print lying flat so the layers run along the hook; PETG.
MAIN PURPOSE: Remove keyboard keycaps safely
Pulls keycaps off a mechanical keyboard evenly without scratching them: slide the two prongs down either side of the cap until the hooks catch under it, then lift straight up.
Printing notes
10.5 cm³
Volume
13.0 g
Est. weight
880
Triangles
Prints as shown on its outline, no supports.
MAIN PURPOSE: Hang bags behind a car seat
Clips round a front-seat headrest post and holds a handbag or shopping bag behind the seat, off the floor and out of the footwell.
Printing notes
10.4 cm³
Volume
12.9 g
Est. weight
824
Triangles
Print lying flat in PETG or ASA (car interiors get hot).