Showcase

Models Showcase

Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category

All Kitchen Desk & office Workshop Bedroom & bathroom Others
Preview of Bleed Cup
By Krypto
Complexity
Medium
Others Home hardware & architecture
0
Bleed Cup
MAIN PURPOSE: Catch the water when bleeding radiators
Hold it under the radiator valve with the key through the front notch: the cup catches the hiss of air and the spurt of dirty water while you open the valve, instead of a towel and a jam jar. Between uses the radiator key lives in the side holster, so it is never lost.
Printing notes
14.0 cm³
Volume
17.3 g
Est. weight
4,216
Triangles

PETG so it shrugs off hot water. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Fluted Stop
By Krypto
Complexity
Multi-part assembly
Others Home hardware & architecture
0
Fluted Stop
MAIN PURPOSE: Prop a door with a sand-filled column
A fluted column doorstop: fill the hollow shaft with about a kilo of sand or gravel, close the lid with its round finial and stand it against the door. It holds a door open like a cast-iron stop, and on a shelf it reads as a small classical column.
Printing notes
170.6 cm³
Volume
211.5 g
Est. weight
3,160
Triangles

Print in PLA; fill with dry sand and tape the lid shut. Prints as shown on its floor, no supports. The lid prints as a separate part, top down.

AR view Open in app
Preview of Sift Floor
By Krypto
Complexity
Advanced
Others Drawer & cabinet organisers
0
Sift Floor
MAIN PURPOSE: Keep crumbs from collecting in drawer bays
A cutlery drawer insert with a slotted floor raised on 4 mm feet: crumbs, grit and drips fall straight through instead of packing into the corners of every bay, so cleaning means lifting the insert out and wiping the drawer, not picking out each fork.
Printing notes
109.1 cm³
Volume
135.2 g
Est. weight
11,416
Triangles

Food-safe PETG. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Stemline
By Krypto
Complexity
Simple
Others Drawer & cabinet organisers
0
Stemline
MAIN PURPOSE: Hang wine glasses under a shelf
Screw it under a kitchen shelf or wall cupboard and slide wine glasses in by their feet: they hang upside down in a row, dust-free and out of the cupboard, which frees a whole shelf. Each 250 mm rail holds four glasses with feet up to 85 mm.
Printing notes
55.4 cm³
Volume
68.7 g
Est. weight
612
Triangles

PETG; print with support under the two ledges. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Gallery Cross
By Krypto
Complexity
Simple (set)
Others Home hardware & architecture
0
Gallery Cross
MAIN PURPOSE: Space a grid of picture frames evenly
Hanging a grid of frames: hold the cross where four frame corners meet and butt each frame against its arms. The 50 mm arms set the gap between frames both ways at once, so a gallery wall of six or nine pictures comes out evenly spaced and square without measuring every gap.
Printing notes
67.5 cm³
Volume
83.7 g
Est. weight
2,680
Triangles

PLA, printed flat; print two for big walls. Prints flat as a plate, no supports.

AR view Open in app
Preview of Mend Card
By Krypto
Complexity
Medium
Others Travel & everyday carry
0
Mend Card
MAIN PURPOSE: Carry a needle and thread in the wallet
A credit-card sized mending kit for the wallet: wind black, white and navy thread between the edge notches, weave two needles through the tiny holes and tuck the end of each thread into the side slit. A lost button or split seam on a trip gets fixed in five minutes.
Printing notes
9.0 cm³
Volume
11.1 g
Est. weight
3,620
Triangles

PETG, printed flat. Prints flat as a plate, no supports.

AR view Open in app
Preview of Table Perch
By Krypto
Complexity
Simple
Others Travel & everyday carry
0
Table Perch
MAIN PURPOSE: Hang a bag under a cafe table
Rest the pad on a café or restaurant table so the hook hangs over the edge: the J curls back under the table top, so a handbag or laptop bag hangs off the floor, out of the aisle and against your knees where nobody can lift it. Flat enough for a coat pocket.
Printing notes
40.3 cm³
Volume
49.9 g
Est. weight
584
Triangles

Print it lying on its side (the profile flat on the bed) in PETG. Stick a felt pad under the top.

AR view Open in app
Preview of Haul Hook
By Krypto
Complexity
Simple
Others Travel & everyday carry
0
Haul Hook
MAIN PURPOSE: Carry several shopping bags comfortably
Slip the handles of three or four shopping bags into the hook and carry them all by the 90 mm grip bar: the weight spreads across your whole palm instead of cutting into your fingers, and the J keeps the handles together so the bags stop swinging apart. Lives in the car door pocket.
Printing notes
70.4 cm³
Volume
87.3 g
Est. weight
848
Triangles

Print it lying on its side (the profile flat on the bed) in PETG.

AR view Open in app
Preview of Key Bangle
By Krypto
Complexity
Simple
Others Travel & everyday carry
0
Key Bangle
MAIN PURPOSE: Wear a locker or house key on the wrist
A flexible bracelet for the locker key: slip the open cuff over your wrist and hang the key ring on the tab, so the key stays on you in the pool, at the gym, on a run or on the beach instead of in a pocket you do not have. Print it in TPU so it springs round any wrist.
Printing notes
16.4 cm³
Volume
20.4 g
Est. weight
1,684
Triangles

TPU, printed flat. Prints as shown on its outline, no supports.

AR view Open in app
Preview of Socket Saddle
By Krypto
Complexity
Simple
Others Travel & everyday carry
0
Socket Saddle
MAIN PURPOSE: Hold a charging phone at a low socket
Unplug the phone charger, slip the slot in the back plate over its pins and plug it back in: the charger now holds the saddle to the wall and the phone rests in the pocket below with its cable looped in, instead of on the floor of a hotel room, airport or station with low sockets.
Printing notes
7.2 cm³
Volume
8.9 g
Est. weight
1,660
Triangles

PETG; the plate is only 2.4 mm so the pins still seat fully. Prints as shown on its floor, no supports.

AR view Open in app

SO3D.xyz is free and built by one maker. Help keep it running.

Be one of the first supporters this month.
Support · Buy me a coffeeSee the Hobbyist plan