Showcase

Models Showcase

Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category

All Kitchen Desk & office Workshop Bedroom & bathroom Others
Preview of Hasselback potato cradle
By Krypto
Complexity
Simple
Kitchen Food preparation
0
Hasselback potato cradle
MAIN PURPOSE: Slice potatoes deep without cutting through
Lay a potato in the curved trough and slice across it every few millimetres: the knife lands on the two 10 mm rails before it reaches the bottom, so every cut stops at the same depth and the potato stays in one fanned piece. Works for accordion cucumbers and courgettes too.
Printing notes
31.8 cm³
Volume
39.5 g
Est. weight
1,364
Triangles

Food-safe PETG. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Fermentation follower disc
By Krypto
Complexity
Medium
Kitchen Food preparation
0
Fermentation follower disc
MAIN PURPOSE: Keep fermenting vegetables submerged
Keeps sauerkraut and kimchi under the brine in a wide-mouth jar: the disc presses the cabbage down, the holes let brine rise above it, and the knob lifts it out without fishing with your fingers.
Printing notes
24.2 cm³
Volume
30.0 g
Est. weight
1,496
Triangles

For food contact, print in a food-safe PETG and wash by hand. Prints flat as a plate, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Fresh pasta nest drying tray
By Krypto
Complexity
Medium
Kitchen Food preparation
0
Fresh pasta nest drying tray
MAIN PURPOSE: Dry fresh pasta nests
Dry six nests of fresh tagliatelle or pappardelle: each nest sits in its own rounded cell and the perforated floor lets air reach underneath, so the pasta dries evenly without sticking.
Printing notes
110.3 cm³
Volume
136.8 g
Est. weight
18,500
Triangles

For food contact, print in a food-safe PETG and wash by hand. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Ravioli cutting grid
By Krypto
Complexity
Advanced
Kitchen Food preparation
0
Ravioli cutting grid
MAIN PURPOSE: Shape and seal ravioli
Cuts eight ravioli at once: lay a sheet of pasta over the fillings, press the grid down so its walls seal and cut the squares, and the vent holes let trapped air out. Print it as shown, then turn it over so the floor becomes the top.
Printing notes
43.6 cm³
Volume
54.1 g
Est. weight
2,352
Triangles

For food contact, print in a food-safe PETG and wash by hand. Print floor-down as shown, then turn it over to use it.

AR view Open in app
Preview of Egg yolk separator cup
By Krypto
Complexity
Medium
Kitchen Food preparation
0
Egg yolk separator cup
MAIN PURPOSE: Separate egg yolks from whites
Crack an egg into the cup: the yolk stays in the middle while the white slips through the four slots into the bowl below. The handle hooks over the bowl rim.
Printing notes
24.4 cm³
Volume
30.2 g
Est. weight
4,280
Triangles

For food contact, print in a food-safe PETG and wash by hand. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Jar lid gripper pad
By Krypto
Complexity
Medium
Kitchen Food preparation
0
Jar lid gripper pad
MAIN PURPOSE: Open stuck jar lids
A ribbed pad that gives a firm grip on stuck jar lids: lay it over the lid and twist. It helps anyone with arthritis or wet hands, and doubles as a coaster.
Printing notes
56.1 cm³
Volume
69.6 g
Est. weight
9,440
Triangles

Print in TPU for the best grip. Prints flat as a plate, no supports.

AR view Open in app
Preview of Rice rinsing bowl with drain wall
By Krypto
Complexity
Medium
Kitchen Food preparation
0
Rice rinsing bowl with drain wall
MAIN PURPOSE: Rinse rice and grains
Rinse rice in the bowl, then tip it towards the low perforated side: the cloudy water pours out through the small holes and the grains stay behind.
Printing notes
88.8 cm³
Volume
110.1 g
Est. weight
13,592
Triangles

For food contact, print in a food-safe PETG and wash by hand. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Tofu press box
By Krypto
Complexity
Multi-part assembly
Kitchen Food preparation
0
Tofu press box
MAIN PURPOSE: Press water out of tofu
Presses water out of a block of tofu: the tofu sits in the top box with a drain floor, the base catches the water, and the flat lid takes a weight such as a can or a jar.
Printing notes
175.9 cm³
Volume
218.1 g
Est. weight
5,028
Triangles

For food contact, print in a food-safe PETG and wash by hand. Prints as shown on its floor, no supports. The added base's lid prints separately. Stacked parts are fused into one print.

AR view Open in app
Preview of Bread slicing guide
By Krypto
Complexity
Medium
Kitchen Food preparation
0
Bread slicing guide
MAIN PURPOSE: Slice bread evenly
Cut even slices from a home-baked loaf: set the loaf in the open-ended frame and saw down through the facing slots, and every slice comes out the same thickness.
Printing notes
71.1 cm³
Volume
88.1 g
Est. weight
1,372
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Sushi rice mixing tub
By Krypto
Complexity
Simple
Kitchen Food preparation
0
Sushi rice mixing tub
MAIN PURPOSE: Season and cool sushi rice
A wide, shallow tub for seasoning sushi rice: spread the hot rice out and fold in the vinegar while fanning it, so it cools quickly and turns glossy.
Printing notes
281.5 cm³
Volume
349.1 g
Est. weight
840
Triangles

For food contact, print in a food-safe PETG and wash by hand. Prints as shown on its floor, no supports.

AR view Open in app

SO3D.xyz is free and built by one maker. Help keep it running.

Be one of the first supporters this month.
Support · Buy me a coffeeSee the Hobbyist plan