Showcase
Models Showcase
Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category
MAIN PURPOSE: Swap printed door signs in seconds
A door or desk sign you can change in seconds: slide a printed 20 x 7.5 cm card in from the top under the lips. Screw it to the door first and the card hides the screws.
Printing notes
30.6 cm³
Volume
37.9 g
Est. weight
468
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Hold locomotives upside down for servicing
Lay a locomotive or coach upside down in the rounded channel to clean its wheels or service the motor; the open ends take models longer than the cradle. Line it with foam to protect the paint.
Printing notes
46.2 cm³
Volume
57.2 g
Est. weight
4,150
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Hold paint and screws on a ladder
Sits on top of a stepladder: one half takes a paint tin or a tub of filler, the other has bays for screws and a pencil, and grip feet stop it sliding off while you work.
Printing notes
178.2 cm³
Volume
221.0 g
Est. weight
2,916
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Carry secateurs on your belt
Carry secateurs blade-down on your belt: thread the belt through the two slots in the back, and a drain hole lets sap and rain run out.
Printing notes
9.1 cm³
Volume
11.2 g
Est. weight
4,352
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Hold RC cars with wheels free
A work stand for 1:10 RC cars: set the car on top so its wheels spin free while you tune the motor or change tyres, and carry it to the track by the hand holes. Print it as shown, then turn it over so the floor becomes the top.
Printing notes
48.3 cm³
Volume
59.9 g
Est. weight
2,324
Triangles
Print floor-down as shown, then turn it over to use it. Large holes in the walls may need supports or good bridging.
MAIN PURPOSE: Hold a spray gun while filling
Holds a gravity-feed spray gun upright with its cup level, so you can fill and strain the paint with both hands free; the handle drops into the front notch.
Printing notes
45.8 cm³
Volume
56.7 g
Est. weight
1,116
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Detangle wet or curly hair gently
A wide-tooth comb for working through wet or curly hair without snapping it: fourteen long, round-tipped teeth on a stiff, comfortable spine.
Printing notes
31.7 cm³
Volume
39.3 g
Est. weight
800
Triangles
Prints flat as a plate, no supports.
MAIN PURPOSE: Divide clothes on the wardrobe rail
Slip it onto the wardrobe rail through the slot to divide clothes by size, child, season or day of the week; change the letter to S, L, a name or a day before printing.
Printing notes
17.6 cm³
Volume
21.8 g
Est. weight
1,144
Triangles
Prints flat as a plate, no supports.
MAIN PURPOSE: Stop stacks toppling on wardrobe shelves
Slide it over the front of a wardrobe shelf up to 19 mm thick and it stands upright to stop stacks of jumpers, towels or bags toppling into each other.
Printing notes
168.1 cm³
Volume
208.5 g
Est. weight
156
Triangles
Prints flat as a plate, no supports.
MAIN PURPOSE: Steady a nail polish bottle while painting
Paint your nails without knocking the bottle over: it stands in the centre ring of a wide, grippy base, and the outer channel holds a cuticle stick and an orange stick.
Printing notes
44.7 cm³
Volume
55.4 g
Est. weight
1,168
Triangles
Prints as shown on its floor, no supports.