Showcase
Models Showcase
Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category
MAIN PURPOSE: Keep drinks off a busy desk
Clamps to a desk top up to 25 mm thick and holds a mug, a can or a water bottle just off the edge, so drinks never end up over the keyboard.
Printing notes
53.5 cm³
Volume
66.3 g
Est. weight
1,112
Triangles
Print lying flat in PETG.
MAIN PURPOSE: Hold rice paddle and measuring cup
Hang it beside the rice cooker: the paddle stands in the narrow slot, the measuring cup in the wide bay, and both drain through holes in the floor.
Printing notes
51.4 cm³
Volume
63.8 g
Est. weight
1,844
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Hold oysters steady while shucking
Shucking without the tea towel: the oyster sits cupped side down in a shell-shaped recess that stops it skidding while you work the knife into the hinge, and grip feet hold the cradle to the board.
Printing notes
282.6 cm³
Volume
350.4 g
Est. weight
1,484
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Build a stackable honeycomb wine rack
One cell of a honeycomb wine rack: print several, lay them on their sides and stack them. The bottle slides in neck first, its shoulder resting against the end wall while the neck pokes through.
Printing notes
115.9 cm³
Volume
143.7 g
Est. weight
236
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Butter bread easily with one hand
For anyone cooking with one hand: push a slice of bread into the raised corner and it stays put while you spread it. Grip feet stop the board sliding.
Printing notes
176.9 cm³
Volume
219.3 g
Est. weight
84
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Help one-handed eaters scoop food
A plate for eating one-handed or with a weak grip: food pushed towards the tall, curved back wall rolls up onto the spoon instead of off the edge, and grip feet hold the plate still.
Printing notes
146.5 cm³
Volume
181.6 g
Est. weight
1,678
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Support a loaded paper plate
A rigid holder for a 23 cm (9-inch) paper plate at picnics and barbecues, so a loaded plate never folds in your hand.
Printing notes
117.4 cm³
Volume
145.5 g
Est. weight
680
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Hold a book open one-handed
Slip your thumb through the ring and the two wings hold a paperback open on both sides, so you can read one-handed on the sofa, the train or the beach.
Printing notes
8.4 cm³
Volume
10.4 g
Est. weight
500
Triangles
Prints flat as a plate, no supports.
MAIN PURPOSE: Park the mouse out of the way
Park the mouse under a little roof at the end of the day so it stays dust-free and out of the way; the cable runs out through a hole in the back. Print it as shown, then turn it over so the floor becomes the top.
Printing notes
33.4 cm³
Volume
41.4 g
Est. weight
3,060
Triangles
Print floor-down as shown, then turn it over to use it.
MAIN PURPOSE: Hold pens beside a built-in clock
A desk tidy with a 55 mm clock fit-up set into the front: the clock has its own front pocket, with pen bays behind it and beside it.
Printing notes
83.3 cm³
Volume
103.3 g
Est. weight
3,072
Triangles
Prints as shown on its floor, no supports. Large holes in the walls may need supports or good bridging.