Showcase

Models Showcase

Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category

All Kitchen Desk & office Workshop Bedroom & bathroom Others
Preview of Line-pointer page clip
By Krypto
Complexity
Simple (set)
Desk & office Paper & bookbinding
0
Line-pointer page clip
MAIN PURPOSE: Mark the exact line where you stopped reading
Slip the clip onto the page edge with its point at the line where you stopped: next time you go straight back to the right line, not just the right page. It is thin enough to stay in while the book is closed.
Printing notes
2.1 cm³
Volume
2.6 g
Est. weight
636
Triangles

Print several in PETG. Prints as shown on its outline, no supports.

AR view Open in app
Preview of Book scanning cradle ends
By Krypto
Complexity
Simple (set)
Desk & office Paper & bookbinding
0
Book scanning cradle ends
MAIN PURPOSE: Hold an open book for scanning without strain
Stand the two V-shaped ends under an open book: the 120 degree cradle supports the covers so the spine is not forced flat, and both pages face the camera for scanning or photographing a fragile book. Print two.
Printing notes
74.8 cm³
Volume
92.8 g
Est. weight
716
Triangles

Print two. Prints as shown on its outline, no supports.

AR view Open in app
Preview of Weighted cable-end anchor
By Krypto
Complexity
Simple
Desk & office Cables & charging
0
Weighted cable-end anchor
MAIN PURPOSE: Stop charging cables sliding off the desk
Snap the charging cables into the three keyhole slots and fill the block with coins: when you unplug the phone, the cable ends stay on the desk instead of sliding off the back and down behind it.
Printing notes
22.2 cm³
Volume
27.5 g
Est. weight
1,912
Triangles

Glue felt or rubber underneath. Prints as shown on its outline, no supports.

AR view Open in app
Preview of RJ45 broken-latch repair clip
By Krypto
Complexity
Simple (set)
Desk & office Cables & charging
0
RJ45 broken-latch repair clip
MAIN PURPOSE: Fix a network cable with a snapped latch
Slide the clip sideways over the body of a network plug whose latch has snapped off: its own springy tongue catches in the socket again, so the cable stays plugged in without crimping a new connector.
Printing notes
1.3 cm³
Volume
1.6 g
Est. weight
528
Triangles

Print in PETG; print a few. Prints as shown on its outline, no supports.

AR view Open in app
Preview of Monitor arm cable clip
By Krypto
Complexity
Simple (set)
Desk & office Cables & charging
0
Monitor arm cable clip
MAIN PURPOSE: Route cables along a monitor arm
Snap the big C onto a 30 mm monitor arm and the cables into the small one: the cables follow the arm wherever you swing the screen instead of hanging in a loop behind it.
Printing notes
4.0 cm³
Volume
4.9 g
Est. weight
1,248
Triangles

Print three or four in PETG. Prints as shown on its outline, no supports.

AR view Open in app
Preview of Stackable flying altitude risers
By Krypto
Complexity
Simple (set)
Others Tabletop gaming & play
0
Stackable flying altitude risers
MAIN PURPOSE: Show how high a flying miniature is
A 25 mm miniature base drops into the top of a riser and each riser nests into the next by its grip foot: every level lifts the model 12 mm and stands for 10 ft of altitude, so flying creatures show their height at a glance and range checks become simple counting instead of notes on paper.
Printing notes
2.8 cm³
Volume
3.5 g
Est. weight
2,088
Triangles

Print six or more. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Player-board edge track slider
By Krypto
Complexity
Simple
Others Tabletop gaming & play
0
Player-board edge track slider
MAIN PURPOSE: Mark track positions that cannot be knocked off
Clips over the 2 mm edge of a player board and slides along it, with a pointed arm that reaches over the printed score or resource track: unlike a loose cube, the marker cannot be knocked off or nudged one space by an elbow, and the spring jaw holds it on the right square.
Printing notes
1.1 cm³
Volume
1.4 g
Est. weight
344
Triangles

Print one per track in each player colour; PETG springs best. Prints as shown on its outline, no supports.

AR view Open in app
Preview of Shape-coded cube caps for colour-blind players
By Krypto
Complexity
Simple (set)
Others Tabletop gaming & play
0
Shape-coded cube caps for colour-blind players
MAIN PURPOSE: Make player pieces readable without colour
A thin hexagonal shell drops over a standard 8 mm wooden cube, so one player's cubes are recognisable by shape as well as colour. Print the other players' sets in the triangle, heart, gear or star base types and nobody has to ask which red is which again. Print it as shown, then turn it over so the floor becomes the top.
Printing notes
0.7 cm³
Volume
0.9 g
Est. weight
68
Triangles

Print a set per player in their colour. Print floor-down as shown, then turn it over to use it.

AR view Open in app
Preview of Line-of-sight laser turret
By Krypto
Complexity
Simple
Others Tabletop gaming & play
0
Line-of-sight laser turret
MAIN PURPOSE: Check true line of sight for a miniature
Stands on the miniature's 25 mm footprint and holds a 12 mm keychain laser crosswise at 27 mm, the eye height of a 28 mm figure: turn the tower and the dot shows exactly what the model can see past terrain, ending arguments that leaning over the table never settles.
Printing notes
3.0 cm³
Volume
3.7 g
Est. weight
444
Triangles

Check the bore against your laser pointer. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Peek-window dice cup for bluffing games
By Krypto
Complexity
Simple
Others Tabletop gaming & play
0
Peek-window dice cup for bluffing games
MAIN PURPOSE: Hide your dice from everyone but yourself
Shake, slam the cup down and keep it there: a narrow slit near the rim faces you, so you can read your own dice at table level while nobody else can, which is the whole of Liar's Dice and Perudo without cupped hands and accidental reveals. Print it as shown, then turn it over so the floor becomes the top.
Printing notes
15.4 cm³
Volume
19.1 g
Est. weight
3,532
Triangles

Print one per player. Print floor-down as shown, then turn it over to use it.

AR view Open in app

SO3D.xyz is free and built by one maker. Help keep it running.

Be one of the first supporters this month.
Support · Buy me a coffeeSee the Hobbyist plan