Showcase
Models Showcase
Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category
MAIN PURPOSE: Hang wine glasses under a shelf
Screw it under a kitchen shelf or wall cupboard and slide wine glasses in by their feet: they hang upside down in a row, dust-free and out of the cupboard, which frees a whole shelf. Each 250 mm rail holds four glasses with feet up to 85 mm.
Printing notes
55.4 cm³
Volume
68.7 g
Est. weight
612
Triangles
PETG; print with support under the two ledges. Prints as shown on its floor, no supports.
MAIN PURPOSE: Space a grid of picture frames evenly
Hanging a grid of frames: hold the cross where four frame corners meet and butt each frame against its arms. The 50 mm arms set the gap between frames both ways at once, so a gallery wall of six or nine pictures comes out evenly spaced and square without measuring every gap.
Printing notes
67.5 cm³
Volume
83.7 g
Est. weight
2,680
Triangles
PLA, printed flat; print two for big walls. Prints flat as a plate, no supports.
MAIN PURPOSE: Hang a bag under a cafe table
Rest the pad on a café or restaurant table so the hook hangs over the edge: the J curls back under the table top, so a handbag or laptop bag hangs off the floor, out of the aisle and against your knees where nobody can lift it. Flat enough for a coat pocket.
Printing notes
40.3 cm³
Volume
49.9 g
Est. weight
584
Triangles
Print it lying on its side (the profile flat on the bed) in PETG. Stick a felt pad under the top.
MAIN PURPOSE: Carry several shopping bags comfortably
Slip the handles of three or four shopping bags into the hook and carry them all by the 90 mm grip bar: the weight spreads across your whole palm instead of cutting into your fingers, and the J keeps the handles together so the bags stop swinging apart. Lives in the car door pocket.
Printing notes
70.4 cm³
Volume
87.3 g
Est. weight
848
Triangles
Print it lying on its side (the profile flat on the bed) in PETG.
MAIN PURPOSE: Wear a locker or house key on the wrist
A flexible bracelet for the locker key: slip the open cuff over your wrist and hang the key ring on the tab, so the key stays on you in the pool, at the gym, on a run or on the beach instead of in a pocket you do not have. Print it in TPU so it springs round any wrist.
Printing notes
16.4 cm³
Volume
20.4 g
Est. weight
1,684
Triangles
TPU, printed flat. Prints as shown on its outline, no supports.
MAIN PURPOSE: Hold a charging phone at a low socket
Unplug the phone charger, slip the slot in the back plate over its pins and plug it back in: the charger now holds the saddle to the wall and the phone rests in the pocket below with its cable looped in, instead of on the floor of a hotel room, airport or station with low sockets.
Printing notes
7.2 cm³
Volume
8.9 g
Est. weight
1,660
Triangles
PETG; the plate is only 2.4 mm so the pins still seat fully. Prints as shown on its floor, no supports.
MAIN PURPOSE: Hold a phone or list on a shopping trolley
Snap it onto the handle of a supermarket trolley or basket and stand your phone or paper shopping list in the fork: the list stays in front of you at eye level and both hands stay free for the shelves. Fits handles 28 to 32 mm and phones up to 15 mm thick in a case.
Printing notes
37.0 cm³
Volume
45.9 g
Est. weight
872
Triangles
Print it lying on its side (the profile flat on the bed) in PETG.
MAIN PURPOSE: Tap a transit card without taking it out
Slide the sleeve onto the shoulder strap of your backpack and push your transit or office pass into the front channel: at the ticket gate or door reader you tap your shoulder, through the 46 mm window, instead of digging through pockets. The card cannot slip out sideways and the strap slides in through the side gap.
Printing notes
29.0 cm³
Volume
35.9 g
Est. weight
1,044
Triangles
PETG, printed standing on end so the channel is clean.
MAIN PURPOSE: Add a bedside shelf to a bunk or berth
Hook it over the guard rail of a bunk, sleeper train berth or hostel bed: the 70 mm shelf sits on the mattress side at pillow height and holds phone, glasses and earplugs within reach in the dark, instead of lost in the sheets. Fits rails up to 26 mm thick.
Printing notes
128.8 cm³
Volume
159.7 g
Est. weight
472
Triangles
Print it lying on its side (the profile flat on the bed) in PETG.
MAIN PURPOSE: Add a handle to a takeaway coffee cup
Slide the split ring up a paper takeaway cup until it wedges on the taper: the hot cup now has a proper handle, so you can carry it without a sleeve or burnt fingers, and it slips off and back into your bag when the cup goes in the recycling. Fits most 12 oz cups.
Printing notes
12.1 cm³
Volume
15.0 g
Est. weight
712
Triangles
PETG, printed flat. Prints flat as a plate, no supports.