Showcase
Models Showcase
Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category
MAIN PURPOSE: Mark the exact line where you stopped reading
Slip the clip onto the page edge with its point at the line where you stopped: next time you go straight back to the right line, not just the right page. It is thin enough to stay in while the book is closed.
Printing notes
2.1 cm³
Volume
2.6 g
Est. weight
636
Triangles
Print several in PETG. Prints as shown on its outline, no supports.
MAIN PURPOSE: Hold an open book for scanning without strain
Stand the two V-shaped ends under an open book: the 120 degree cradle supports the covers so the spine is not forced flat, and both pages face the camera for scanning or photographing a fragile book. Print two.
Printing notes
74.8 cm³
Volume
92.8 g
Est. weight
716
Triangles
Print two. Prints as shown on its outline, no supports.
MAIN PURPOSE: Stop charging cables sliding off the desk
Snap the charging cables into the three keyhole slots and fill the block with coins: when you unplug the phone, the cable ends stay on the desk instead of sliding off the back and down behind it.
Printing notes
22.2 cm³
Volume
27.5 g
Est. weight
1,912
Triangles
Glue felt or rubber underneath. Prints as shown on its outline, no supports.
MAIN PURPOSE: Fix a network cable with a snapped latch
Slide the clip sideways over the body of a network plug whose latch has snapped off: its own springy tongue catches in the socket again, so the cable stays plugged in without crimping a new connector.
Printing notes
1.3 cm³
Volume
1.6 g
Est. weight
528
Triangles
Print in PETG; print a few. Prints as shown on its outline, no supports.
MAIN PURPOSE: Route cables along a monitor arm
Snap the big C onto a 30 mm monitor arm and the cables into the small one: the cables follow the arm wherever you swing the screen instead of hanging in a loop behind it.
Printing notes
4.0 cm³
Volume
4.9 g
Est. weight
1,248
Triangles
Print three or four in PETG. Prints as shown on its outline, no supports.
MAIN PURPOSE: Cover a webcam when not in use
A slim clip that slides over the top edge of a laptop lid or monitor up to 7 mm thick, hiding the webcam until you slide it aside for a call.
Printing notes
3.1 cm³
Volume
3.9 g
Est. weight
392
Triangles
Print as it comes (clip outline on the bed), 0.12 mm layers.
MAIN PURPOSE: Stop ink bottles tipping over
A wide base that keeps a fountain pen ink bottle from being knocked over while you fill a pen: the bottle sits in the ring and the grip feet hold it to the desk.
Printing notes
50.3 cm³
Volume
62.4 g
Est. weight
1,168
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Use pencils down to the last few centimetres
Lengthens a pencil worn down to a stub so you can use it to the end: push the stub into the tube until it grips.
Printing notes
3.8 cm³
Volume
4.7 g
Est. weight
680
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Fold and crease paper and card
A bookbinder's bone folder for crisp folds and creases in paper and card: run the pointed end along a ruler to score, then the flat side to press the fold.
Printing notes
16.9 cm³
Volume
20.9 g
Est. weight
112
Triangles
Prints flat as a plate, no supports.
MAIN PURPOSE: Close a poster tube
Replaces a lost end cap on a 52 mm poster or document tube; the ribbed rim gives a good grip when you pull it off.
Printing notes
14.2 cm³
Volume
17.6 g
Est. weight
680
Triangles
Prints as shown on its floor, no supports.