Showcase
Models Showcase
Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category
MAIN PURPOSE: Drill evenly spaced shelf-pin holes
Hook the lip over the front edge of a cabinet side and drill a perfectly even row of 5 mm shelf-pin holes on a 32 mm grid, 37 mm in from the edge. Print it as shown, then turn it over so the floor becomes the top.
Printing notes
34.5 cm³
Volume
42.7 g
Est. weight
1,196
Triangles
Print floor-down as shown, then turn it over to use it.
MAIN PURPOSE: Catch dust while drilling walls
Hold the flat back against the wall just below where you drill and the dust falls into the cup instead of onto the floor; the scooped front pours it out.
Printing notes
14.5 cm³
Volume
17.9 g
Est. weight
3,050
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Wind extension cords and fairy lights
A stiff winder for an extension lead, fairy lights or a garden line: the cord wraps the long way round through the notches at each end, with a hole to hang it up.
Printing notes
60.4 cm³
Volume
74.9 g
Est. weight
372
Triangles
Prints flat as a plate, no supports.
MAIN PURPOSE: Store spare 3D printer build sheets
Stand spare 3D printer build sheets on edge in the eight slots like files, so the textured and smooth plates stay flat and clean; print two for big sheets.
Printing notes
58.6 cm³
Volume
72.6 g
Est. weight
1,088
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Check drill bit sharpening angles
Check a re-sharpened drill bit against the 118-degree notch and each cutting lip against the 59-degree edge.
Printing notes
9.0 cm³
Volume
11.1 g
Est. weight
4,692
Triangles
Prints flat as a plate, no supports.
MAIN PURPOSE: Shape silicone and caulk beads
A card with a different profile on every corner for finishing silicone and caulk beads in bathrooms and kitchens: two chamfers, a cove and a step.
Printing notes
15.1 cm³
Volume
18.7 g
Est. weight
144
Triangles
Prints flat as a plate, no supports.
MAIN PURPOSE: Store a retainer or night guard
A kidney-shaped case that takes an upper or lower retainer or a night guard, with a telescoping lid and two air holes in the floor so it dries instead of sweating.
Printing notes
40.3 cm³
Volume
50.0 g
Est. weight
2,112
Triangles
Prints as shown on its outline, no supports. The lid prints as a separate part, top down.
MAIN PURPOSE: Keep a pacifier clean while travelling
A pacifier-shaped travel case that keeps a dummy clean in the changing bag, with a telescoping lid and an air hole so it can dry.
Printing notes
49.0 cm³
Volume
60.8 g
Est. weight
2,792
Triangles
Prints as shown on its outline, no supports. The lid prints as a separate part, top down.
MAIN PURPOSE: Dry spare toothbrush heads upright
Four spare brush heads stand upright through the holes of the top plate and dry in the open air, with drain holes in the floor below.
Printing notes
26.8 cm³
Volume
33.2 g
Est. weight
3,492
Triangles
Prints as shown on its floor, no supports. Stacked parts are fused into one print.
MAIN PURPOSE: File eyeshadow palettes like books
Six upright slots that file eyeshadow and blush palettes like books, with a low front so every lid shows and rounded rims.
Printing notes
137.9 cm³
Volume
171.0 g
Est. weight
2,940
Triangles
Prints as shown on its floor, no supports.