Showcase
Models Showcase
Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category
MAIN PURPOSE: Store hole saws and arbor
A deep fitted case for five hole saws from 25 to 68 mm and their arbor, with a telescoping lid shown beside it.
Printing notes
897.2 cm³
Volume
1,112.6 g
Est. weight
6,600
Triangles
Prints as shown on its floor, no supports. The lid prints as a separate part, top down.
MAIN PURPOSE: Keep drill bits square to work
Two plates 34 mm apart with matching 4, 6, 8 and 10 mm holes keep the bit square to the work: hold the block down and drill straight through.
Printing notes
30.2 cm³
Volume
37.4 g
Est. weight
1,496
Triangles
Prints as shown on its floor, no supports. Stacked parts are fused into one print.
MAIN PURPOSE: Store spudgers, picks and pry tools
A shadow tray for four spudgers, picks and pry tools, with a finger channel across the middle.
Printing notes
114.0 cm³
Volume
141.3 g
Est. weight
2,208
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Spread glue in an even film
A stiff spreader card with fine teeth along one edge for an even film of wood glue or tile adhesive.
Printing notes
9.2 cm³
Volume
11.4 g
Est. weight
636
Triangles
Prints flat as a plate, no supports.
MAIN PURPOSE: Protect a pull saw's teeth
A slim channel that slides over the teeth of a Japanese pull saw, so the blade stays sharp and fingers stay safe in the toolbox.
Printing notes
8.1 cm³
Volume
10.0 g
Est. weight
96
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Clamp box corners at ninety degrees
A rigid 90-degree square for gluing up boxes and frames, with a relief notch in the corner for glue squeeze-out and slots for the clamp jaws.
Printing notes
46.8 cm³
Volume
58.1 g
Est. weight
1,564
Triangles
Prints as shown on its outline, no supports.
MAIN PURPOSE: Tear sandpaper into sander-sized strips
Lay it on a standard sheet with the lip hooked over the edge and tear upwards along the plate for a perfect one-third strip that fits a palm sander. Print it as shown, then turn it over so the floor becomes the top.
Printing notes
69.2 cm³
Volume
85.8 g
Est. weight
48
Triangles
Print floor-down as shown, then turn it over to use it.
MAIN PURPOSE: Measure screw length at a glance
Drop a screw in, butt its head against the left wall and read its length off the raised ticks every 10 mm.
Printing notes
9.0 cm³
Volume
11.2 g
Est. weight
15,996
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Hold circuit boards steady while soldering
A cradle with a groove along each side wall: slide a circuit board in from the open front and it is held flat and steady while you solder.
Printing notes
73.0 cm³
Volume
90.5 g
Est. weight
156
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Drill hinge cup holes accurately
Hook the lip over the door edge and the 35 mm hole sits 22.5 mm in, ready for the cup drill, with the two screw pilot holes marked; check the spacing against your own hinges. Print it as shown, then turn it over so the floor becomes the top.
Printing notes
17.1 cm³
Volume
21.3 g
Est. weight
552
Triangles
Print floor-down as shown, then turn it over to use it.