Showcase
Models Showcase
Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category
MAIN PURPOSE: Sort and stack everyday items in three compartments
A roomy, stackable storage box with three compartments: one large section and two smaller ones side by side. It suits tools, craft supplies, chargers and cables, toiletries, snacks or toys. As it comes it's 210 × 210 × 63 mm with 2 mm walls and softly rounded corners. The dividers sit a little lower than the walls, so things are easy to reach. Every dimension can be changed in the editor: width, depth, height, wall thickness, corner radius, and the number, position and height of the dividers. That way you can size it for your own drawer, shelf or cupboard. The Raised grip base lets one box stack firmly on another, so you can build a neat tower without anything sliding off. It prints as one solid piece with no supports.
Printing notes
345.1 cm³
Volume
427.9 g
Est. weight
1,924
Triangles
Print upright in PLA or PETG with no supports. Use 3 walls (perimeters) for a sturdier box. Prints as shown on its floor, no supports.
MAIN PURPOSE: Stop detergent caps dripping on the machine
Stand the detergent bottle in the tray and park its measuring cap upside down in the round well beside it. The last drops run into the well instead of onto the washing machine.
Printing notes
51.9 cm³
Volume
64.4 g
Est. weight
816
Triangles
Size the well to your cap. Prints as shown on its floor, no supports.
MAIN PURPOSE: Keep robot vacuum brushes, filters and mop pads ready
A spares box for robot vacuums: the long bay takes a main roller brush, the others hold side brushes, filters and mop pads, and the label strip records the part numbers for re-ordering. Servicing the robot becomes a two-minute job.
Printing notes
236.5 cm³
Volume
293.2 g
Est. weight
3,064
Triangles
Write the model and part numbers on the label strip. Prints as shown on its floor, no supports. The lid prints as a separate part, top down.
MAIN PURPOSE: Keep crumbs from collecting in drawer bays
A cutlery drawer insert with a slotted floor raised on 4 mm feet: crumbs, grit and drips fall straight through instead of packing into the corners of every bay, so cleaning means lifting the insert out and wiping the drawer, not picking out each fork.
Printing notes
109.1 cm³
Volume
135.2 g
Est. weight
11,416
Triangles
Food-safe PETG. Prints as shown on its floor, no supports.
MAIN PURPOSE: Hang wine glasses under a shelf
Screw it under a kitchen shelf or wall cupboard and slide wine glasses in by their feet: they hang upside down in a row, dust-free and out of the cupboard, which frees a whole shelf. Each 250 mm rail holds four glasses with feet up to 85 mm.
Printing notes
55.4 cm³
Volume
68.7 g
Est. weight
612
Triangles
PETG; print with support under the two ledges. Prints as shown on its floor, no supports.
MAIN PURPOSE: Snap open storage cubes together magnetically
A 60 mm open cube with a pair of 6 x 3 mm magnets in every wall. Fit each wall the same way (north out on the left hole, south on the right) and any face meets any face, so cubes snap into rows, L shapes or towers in a drawer and pull apart to rearrange.
Printing notes
12.3 cm³
Volume
15.2 g
Est. weight
2,336
Triangles
Glue 16 x 6 x 3 mm magnets flush, polarity as described. Prints as shown on its floor, no supports.
MAIN PURPOSE: Build a crossing divider grid for any drawer
Drawer dividers that cross like an egg crate, no hardboard or clips needed: each 200 x 40 mm strip has slots half-way down at a 30 mm pitch. Turn every other strip upside down and they slot together into a grid of any cell size, then snap a strip shorter along a slot to fit the drawer.
Printing notes
15.3 cm³
Volume
19.0 g
Est. weight
420
Triangles
Print flat in PETG, 2 mm; print six to ten.
MAIN PURPOSE: Anchor divider strips to a drawer wall
The wall rail for Gridlap: a 200 mm comb with 2.4 mm slots on the same 30 mm pitch, stuck to the drawer side with foam tape. Strip ends drop into its teeth, so a grid holds square to the wall and T-junctions work without crossing strips.
Printing notes
657.3 cm³
Volume
815.1 g
Est. weight
1,888
Triangles
Print as it comes (comb on the bed), solid; fix with foam tape.
MAIN PURPOSE: Use the space around a sink waste pipe
A U-shaped caddy that wraps round the sink waste trap instead of fighting it: the 90 mm slot slides in round the pipe from the front, so the whole cupboard floor holds bottles and sponges, and the caddy lifts out by its two arms for wiping.
Printing notes
415.0 cm³
Volume
514.6 g
Est. weight
760
Triangles
Prints as shown on its outline, no supports.
MAIN PURPOSE: Add a second level inside a deep drawer
Stand it in a deep drawer and the drawer gets two floors: small things live in the tray on top, while flat items such as placemats, chargers or envelopes slide underneath through the open front and back. Lift the bridge out to reach them.
Printing notes
107.2 cm³
Volume
132.9 g
Est. weight
1,076
Triangles
Prints as shown on its floor, no supports. Stacked parts are fused into one print.