Showcase

Models Showcase

Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category

All Kitchen Desk & office Workshop Bedroom & bathroom Others
Preview of Cold Hang
By Krypto
Complexity
Simple
Kitchen Coffee & tea
0
Cold Hang
MAIN PURPOSE: Hang a cold brew bag in a jar
Rest the bridge on the mouth of a wide jar and hang a cold brew coffee or tea filter bag from the bar by its drawstring: the bag stays submerged without sinking to the bottom or flopping against the glass, and next morning you lift bridge and bag out together to drip over the sink.
Printing notes
24.5 cm³
Volume
30.4 g
Est. weight
1,648
Triangles

Food-safe PETG. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Airfall Caddy
By Krypto
Complexity
Multi-part assembly
Kitchen Coffee & tea
0
Airfall Caddy
MAIN PURPOSE: Keep loose tea fresh under a slow-closing lid
A tea caddy with an air-cushioned lid: the snug telescoping lid traps air as it goes on, so it sinks slowly under its own weight and closes with a soft sigh, like a Japanese chazutsu. The tight fit keeps leaves fresh; engrave the tea name on the front.
Printing notes
37.5 cm³
Volume
46.4 g
Est. weight
8,408
Triangles

Print with 4 walls so the sides are airtight; ease fit to standard if tight. Prints as shown on its floor, no supports. The lid prints as a separate part, top down.

AR view Open in app
Preview of Pagoda Stack
By Krypto
Complexity
Medium
Kitchen Coffee & tea
0
Pagoda Stack
MAIN PURPOSE: Store teas in storeys whose eaves are lids
Stacking tea caddies built on pagoda logic: every storey wears a wide octagonal eave, and the eave of the storey above is the lid of the one below. Stack three, four or five, one tea in each, and lift off the upper storeys to reach the one you want.
Printing notes
55.3 cm³
Volume
68.6 g
Est. weight
120
Triangles

Print as many storeys as teas; add a fifth eave as the top cap. Prints flat as a plate, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Espresso puck leveller with depth flange
By Krypto
Complexity
Advanced
Kitchen Coffee & tea
0
Espresso puck leveller with depth flange
MAIN PURPOSE: Level espresso grounds before tamping
Rest the flange on the rim of a 58 mm basket and turn the leveller a few times: the flat face sits 4 mm below the rim and sweeps the grounds into an even, level bed before tamping, which stops channelling. Print the body 1 mm taller for smaller doses.
Printing notes
38.4 cm³
Volume
47.6 g
Est. weight
2,040
Triangles

Food-safe PETG; the flange prints as a small overhang. Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Loose-leaf tea portion scoop
By Krypto
Complexity
Medium
Kitchen Coffee & tea
0
Loose-leaf tea portion scoop
MAIN PURPOSE: Measure loose-leaf tea by the cup
Three wells sized for one, two and four cups (5, 10 and 20 ml): dip, level with a finger and tip into the pot, so loose-leaf tea comes out the same strength every time without a set of spoons.
Printing notes
12.7 cm³
Volume
15.7 g
Est. weight
3,490
Triangles

Food-safe PETG. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Tea bag squeeze tongs
By Krypto
Complexity
Simple
Kitchen Coffee & tea
0
Tea bag squeeze tongs
MAIN PURPOSE: Lift and squeeze a hot tea bag cleanly
Lift the tea bag out of the mug with the paddles, give it a squeeze over the cup and drop it in the bin: the U spring opens the tongs again on its own, so no burnt fingers and no spoon dripping on the worktop.
Printing notes
10.2 cm³
Volume
12.6 g
Est. weight
604
Triangles

Food-safe PETG. Prints flat as a plate, no supports.

AR view Open in app
Preview of Inverted AeroPress safety cradle
By Krypto
Complexity
Medium
Kitchen Coffee & tea
0
Inverted AeroPress safety cradle
MAIN PURPOSE: Keep an inverted AeroPress from tipping
Stand an inverted AeroPress with its plunger end in the 66 mm cup while the coffee steeps: the cradle stops the tall, top-heavy press from tipping over and the dish catches any drips, which makes the inverted method safe on a crowded worktop.
Printing notes
58.8 cm³
Volume
72.9 g
Est. weight
1,360
Triangles

Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Espresso dosing funnel for 58 mm baskets
By Krypto
Complexity
Simple
Kitchen Coffee & tea
0
Espresso dosing funnel for 58 mm baskets
MAIN PURPOSE: Grind into a portafilter without spills
Sits on a 58 mm portafilter while you grind straight into it, so no coffee spills over the rim; lift it off and tamp as usual.
Printing notes
17.8 cm³
Volume
22.0 g
Est. weight
848
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Espresso puck screen and distribution tool dock
By Krypto
Complexity
Medium
Kitchen Coffee & tea
0
Espresso puck screen and distribution tool dock
MAIN PURPOSE: Store espresso puck screen and WDT tool
Parks a 58 mm puck screen flat in the left bay and stands a needle distribution tool upright in the round cup, so both stay clean beside the machine.
Printing notes
57.4 cm³
Volume
71.1 g
Est. weight
1,696
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Coffee press paper filter caddy
By Krypto
Complexity
Multi-part assembly
Kitchen Coffee & tea
0
Coffee press paper filter caddy
MAIN PURPOSE: Store round coffee filters and the scoop
Keeps a stack of round 64 mm paper filters for a travel coffee press clean and flat, with a side tube for the scoop and the stirrer.
Printing notes
80.4 cm³
Volume
99.8 g
Est. weight
2,232
Triangles

Prints as shown on its floor, no supports. The friction-fit lid and its neck piece print separately; adjust Fit in the Lid tab if it binds.

AR view Open in app

SO3D.xyz is free and built by one maker. Help keep it running.

Be one of the first supporters this month.
Support · Buy me a coffeeSee the Hobbyist plan