Showcase
Models Showcase
Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category
MAIN PURPOSE: Turn an upturned bucket into a side table
A table top for an upturned bucket or planter. Print it, flip it, and the deep skirt drops over the base of a storage bucket, so a tub of blankets or toys becomes a side table with a flat top, and the bucket keeps its storage job.
Printing notes
209.4 cm³
Volume
259.7 g
Est. weight
680
Triangles
Set the diameter to the bucket base plus 4 mm. Prints as shown on its floor, no supports.
MAIN PURPOSE: Steer a ball round a spiral corridor by tilting
A palm-sized tilt game on a coiled corridor: drop an 8 mm steel ball in at the outer end and steer it three turns inwards by circling the board in both hands until it drops into the seat at the heart of the coil. Rush it and the ball races back out round the curve, so it rewards slow, even wrists.
Printing notes
76.4 cm³
Volume
94.8 g
Est. weight
3,256
Triangles
Light colour so the ball shows. Use an 8 mm steel ball. Prints as shown on its outline, no supports.
MAIN PURPOSE: Hold a balance beam on a knife-edge pivot
The pivot for a desk lever lab: a lambda frame of 9 mm legs rising to a rounded knife tip, standing on two foot bars. The Fulcrum Beam rests its arch on the tip, so the pivot sits above the beam and it swings and settles like a real balance. The tip also carries the Moonbalance crescent.
Printing notes
86.0 cm³
Volume
106.7 g
Est. weight
632
Triangles
Print as it comes (profile on the bed); legs come out solid.
MAIN PURPOSE: Show balancing moments with coins and clips
A 249 mm balance beam whose central bridge arch sits on the Fulcrum Stand tip, 18 mm above the beam line so it always swings back level. Eight V notches at matched distances hold paper clips loaded with coins: put two coins at 32 mm and one at 64 mm on the other side and watch the moments cancel.
Printing notes
22.4 cm³
Volume
27.7 g
Est. weight
824
Triangles
Print as it comes (profile on the bed), 100 % solid.
MAIN PURPOSE: Roll marbles between marble run pylons
The track for the Rillway run: a 230 mm open channel with filleted sides for a 16 mm marble, closed at one end and open at the other. Push the closed end into a high pylon window and the open end into a lower window on the facing pylon, so the stop catches each falling marble and the open end drops it on.
Printing notes
11.7 cm³
Volume
14.5 g
Est. weight
432
Triangles
Print three or four. 16 mm glass marbles. Prints as shown on its floor, no supports.
MAIN PURPOSE: Collect marbles at the end of the run
The finish line of the Rillway run: a deep filleted cup with one side wall lowered to 22 mm so the last rail rests on it, open end inside. Marbles drop in, roll round the curved floor and stay put for the next go. FINISH is engraved on the front.
Printing notes
16.0 cm³
Volume
19.9 g
Est. weight
3,976
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Build a self-supporting arch from nine blocks
One stone of a self-supporting arch: print nine of these 20 degree wedges, lay them over the Voussoir Centring, drop in the last as the keystone and pull the centring out. Nothing holds the arch but compression, exactly as in a Roman bridge. The hollow side faces the back.
Printing notes
15.7 cm³
Volume
19.5 g
Est. weight
220
Triangles
Print nine, open side up, same settings for equal weight. Prints as shown on its outline, no supports.
MAIN PURPOSE: Support arch blocks while the arch is built
The temporary form an arch is built on: a solid semicircular rib with foot pads, sized so nine Voussoir Wedges sit on it. Stand it up, lay the wedges from both ends, set the keystone, then slide the centring out sideways and watch the arch carry itself.
Printing notes
87.0 cm³
Volume
107.9 g
Est. weight
840
Triangles
Print as it comes (profile on the bed); the rib is solid.
MAIN PURPOSE: Separate two linked rings through hidden slots
A two-piece disentanglement puzzle: identical 60 mm rings, each with a slot that doglegs through the band. Link them and the slots never line up by accident; there is one turn and slide that frees them. Print two in contrasting colours, and the first move is linking them yourself.
Printing notes
7.2 cm³
Volume
8.9 g
Est. weight
540
Triangles
Print two flat in PETG, 4 mm, in two colours. Prints flat as a plate, no supports.
MAIN PURPOSE: Join two pen cups with a sliding dovetail
Two identical pen cups that slide together on a dovetail into one 80 mm square block, the way Japanese joinery locks timbers. Turn one cup round, lower it onto the other and the tail drops into the socket; lift one off to share it across the desk.
Printing notes
69.5 cm³
Volume
86.2 g
Est. weight
940
Triangles
Print two; same orientation, they mate when one is turned. Prints as shown on its outline, no supports.