Showcase

Models Showcase

Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category

All Kitchen Desk & office Workshop Bedroom & bathroom Others
Preview of 2020 extrusion filament guide clip
By Krypto
Complexity
Simple (set)
Workshop Maker & 3D printing
0
2020 extrusion filament guide clip
MAIN PURPOSE: Guide filament past a printer frame
Snaps into the 6 mm slot of any 2020 aluminium frame and holds a 4 mm PTFE tube 18 mm out from the profile: filament from a top or side spool runs through the tube instead of rubbing a groove into the frame edge and dragging against the extruder.
Printing notes
3.3 cm³
Volume
4.1 g
Est. weight
1,152
Triangles

Print in PETG; print a few along the frame. Prints as shown on its outline, no supports.

AR view Open in app
Preview of Bed-levelling knob quarter-turn caps
By Krypto
Complexity
Simple (set)
Workshop Maker & 3D printing
0
Bed-levelling knob quarter-turn caps
MAIN PURPOSE: Track bed-levelling knob turns
Push a cap over each bed-levelling wheel: the four engraved marks show exactly how far you turned each corner, a quarter turn at a time, so an adjustment can be repeated, halved or undone instead of guessed, and the four corners stop chasing each other.
Printing notes
2.5 cm³
Volume
3.1 g
Est. weight
5,134
Triangles

Print four in TPU so they stretch over knurled 30 mm wheels. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Copper pipe square-marking collar
By Krypto
Complexity
Simple
Workshop Trade & professional tools
0
Copper pipe square-marking collar
MAIN PURPOSE: Mark square cuts on copper pipe
Snap the collar onto 15 or 22 mm copper pipe, slide its flat face to your mark and run a pencil round it: the line is square to the pipe, so the cut sits fully home in compression and solder fittings instead of weeping from a slanted end.
Printing notes
17.4 cm³
Volume
21.5 g
Est. weight
1,324
Triangles

Print in PETG. Prints as shown on its outline, no supports.

AR view Open in app
Preview of Survey pole bull's-eye level clip
By Krypto
Complexity
Simple
Workshop Trade & professional tools
0
Survey pole bull's-eye level clip
MAIN PURPOSE: Hold a survey pole plumb
Snaps onto a 25 mm detail or ranging pole and carries a 25 mm bull's-eye vial in its cup: centre the bubble and the pole is plumb over the point, so stakeout and level readings stop drifting by centimetres at the top of a tall pole.
Printing notes
7.6 cm³
Volume
9.4 g
Est. weight
1,336
Triangles

Glue a 25 mm bull's-eye vial into the cup; print in PETG. Prints as shown on its outline, no supports.

AR view Open in app
Preview of Upholstery tucking tool
By Krypto
Complexity
Simple
Workshop Trade & professional tools
0
Upholstery tucking tool
MAIN PURPOSE: Tuck fabric into furniture frames
A flat, tapering blade on a round handle for pushing fabric, leather and wadding into the gap between seat and frame, with a notch in the tip for guiding piping cord: firm enough to push, smooth enough not to snag or scratch show wood.
Printing notes
12.1 cm³
Volume
15.0 g
Est. weight
296
Triangles

Print in PETG or nylon and sand the blade edge smooth. Prints flat as a plate, no supports.

AR view Open in app
Preview of Picture-hanging nail-position marker
By Krypto
Complexity
Simple
Workshop Trade & professional tools
0
Picture-hanging nail-position marker
MAIN PURPOSE: Mark where a picture hook must go
Hang the picture's wire or cord in the notch, push a panel pin through the hole just below it, then hold the picture where it should go and press: the pin pricks the exact spot for the hook, so the picture hangs where you held it, first time, with no measuring.
Printing notes
11.2 cm³
Volume
13.9 g
Est. weight
288
Triangles

Prints flat as a plate, no supports.

AR view Open in app
Preview of V centre finder for turning blanks
By Krypto
Complexity
Simple
Workshop Woodworking
0
V centre finder for turning blanks
MAIN PURPOSE: Find the centre of round stock
Press a round turning blank, a dowel or a log end into the 90 degree V and draw along the blade, whose edge lies exactly on the bisector; turn the blank a quarter and draw again. The lines cross at the true centre, ready for the drive spur, a chuck or a drill.
Printing notes
13.0 cm³
Volume
16.2 g
Est. weight
204
Triangles

Prints flat as a plate, no supports.

AR view Open in app
Preview of Cambered glue-up cauls
By Krypto
Complexity
Simple (set)
Workshop Woodworking
0
Cambered glue-up cauls
MAIN PURPOSE: Clamp panel glue-ups evenly across their width
Each caul has a 1.5 mm crown along its working face: clamp a pair across a panel at the ends and the crown presses the middle first, so the whole joint closes evenly instead of gaping in the centre. Print four, two for each side of the panel.
Printing notes
82.8 cm³
Volume
102.7 g
Est. weight
188
Triangles

Print four, profile on the bed, in PETG. Prints as shown on its outline, no supports.

AR view Open in app
Preview of Kerf-keeper wedge
By Krypto
Complexity
Simple (set)
Workshop Woodworking
0
Kerf-keeper wedge
MAIN PURPOSE: Stop a saw kerf closing on the blade
When ripping a long board by hand, tap the wedge into the kerf behind the saw: it holds the cut open from 1.5 to 6 mm, so the wood cannot close and pinch the blade, and the saw keeps running free and straight to the end of the cut.
Printing notes
7.6 cm³
Volume
9.4 g
Est. weight
672
Triangles

Print in PETG; print two for long rips. Prints as shown on its outline, no supports.

AR view Open in app
Preview of Winding sticks for checking twist
By Krypto
Complexity
Simple (set)
Workshop Woodworking
0
Winding sticks for checking twist
MAIN PURPOSE: Detect twist in a board before planing
Set one stick across each end of a board and sight across their top edges: if the edges are not parallel, the board is in wind, and you can see exactly which corners to plane down. Print one stick in a light colour and one in a dark colour so the edges stand out against each other.
Printing notes
10.6 cm³
Volume
13.1 g
Est. weight
5,976
Triangles

Print two, in contrasting colours. Prints as shown on its floor, no supports.

AR view Open in app

SO3D.xyz is free and built by one maker. Help keep it running.

Be one of the first supporters this month.
Support · Buy me a coffeeSee the Hobbyist plan