Showcase

Models Showcase

Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category

All Kitchen Desk & office Workshop Bedroom & bathroom Others
Preview of Stackable Storage Box – 3 Compartments (Customisable Size)
By Krypto
Complexity
Medium
Workshop Others Drawer & cabinet organisers
2
Stackable Storage Box – 3 Compartments (Customisable Size)
MAIN PURPOSE: Sort and stack everyday items in three compartments
A roomy, stackable storage box with three compartments: one large section and two smaller ones side by side. It suits tools, craft supplies, chargers and cables, toiletries, snacks or toys. As it comes it's 210 × 210 × 63 mm with 2 mm walls and softly rounded corners. The dividers sit a little lower than the walls, so things are easy to reach. Every dimension can be changed in the editor: width, depth, height, wall thickness, corner radius, and the number, position and height of the dividers. That way you can size it for your own drawer, shelf or cupboard. The Raised grip base lets one box stack firmly on another, so you can build a neat tower without anything sliding off. It prints as one solid piece with no supports.
Printing notes
345.1 cm³
Volume
427.9 g
Est. weight
1,924
Triangles

Print upright in PLA or PETG with no supports. Use 3 walls (perimeters) for a sturdier box. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Electrolysis rust-removal tank
By Krypto
Complexity
Medium
Workshop Finishing & painting
0
Electrolysis rust-removal tank
MAIN PURPOSE: Strip rust off old tools overnight with washing soda and a battery charger
The restorer's secret for rusty tools. Fill the tank with water and a tablespoon of washing soda per litre, slide scrap steel plates into the slots at each end and connect them to the + clip of a 12 V battery charger. Hang the rusty tool from a rod through the two top holes and connect it to the - clip. Tiny bubbles start at once, and by morning the rust has turned to loose black flakes that wipe off, leaving the clean metal and even the stamped markings underneath untouched.
Printing notes
194.8 cm³
Volume
241.5 g
Est. weight
1,468
Triangles

Outdoors or well ventilated only (it makes hydrogen). Never use stainless steel plates, never touch the clips while it is on. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Pen-blank rack
By Krypto
Complexity
Medium
Workshop Woodworking
0
Pen-blank rack
MAIN PURPOSE: Store wooden and acrylic pen-turning blanks upright by species
Pen turners collect blanks like stamps: olive, padauk, burl, acrylic swirls. This rack stands them upright in eight bays by species, with the end grain showing so you can choose at a glance, and a label strip for the stock list. It sits by the lathe.
Printing notes
163.0 cm³
Volume
202.1 g
Est. weight
1,112
Triangles

Blanks are 20 mm square by 130 mm; write the species on the label strip. Prints as shown on its floor, no supports.

AR view Open in app
Preview of 3D-printer scraper dock
By Krypto
Complexity
Medium
Workshop Maker & 3D printing
0
3D-printer scraper dock
MAIN PURPOSE: Park a print scraper and glue stick on the printer enclosure
A dock that lives on the side of a 3D printer: the plate scraper drops blade-down into the slot, the glue stick stands in the round cup, and the front bay takes the deburring tool and nozzle wipe. No more hunting for the scraper with a finished print waiting.
Printing notes
66.0 cm³
Volume
81.8 g
Est. weight
2,188
Triangles

Screw or tape it to the enclosure side; the slot takes scrapers up to 8 mm thick. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Gridfinity lever-connector bin
By Krypto
Complexity
Medium
Workshop Trade & professional tools
0
Gridfinity lever-connector bin
MAIN PURPOSE: Sort lever wire connectors by size in a Gridfinity bin
A 3x2 Gridfinity bin for electricians' lever connectors: six bays for the 2-, 3- and 5-way sizes and the inline splicers, in a bin that clicks into the van's Gridfinity drawer and lifts out to the job.
Printing notes
76.7 cm³
Volume
95.2 g
Est. weight
2,780
Triangles

Snaps into any Gridfinity baseplate. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Stained-glass cutter station
By Krypto
Complexity
Medium
Workshop Crafts & making
0
Stained-glass cutter station
MAIN PURPOSE: Keep a glass cutter oiled with its pliers and breaker
A bench station for stained-glass work. The glass cutter stands wheel-down in the oil cup so the wheel stays lubricated between scores, and the tray holds the running pliers, grozing pliers and breaker. It saves wheels and saves glass.
Printing notes
55.7 cm³
Volume
69.0 g
Est. weight
1,684
Triangles

Put a little sponge and cutting oil in the cup; the cutter wheel rests in it. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Arc Rider
By Krypto
Complexity
Medium
Workshop Tools & jigs
0
Arc Rider
MAIN PURPOSE: Turn a tape measure into a big compass
Slide the clip onto a tape measure blade and push a pencil through the side ring: hook the tape over a nail at the centre point, lock it at the radius you want and swing it, and the pencil draws circles and arcs as large as the tape is long, for arches, round tables and garden beds.
Printing notes
4.7 cm³
Volume
5.8 g
Est. weight
980
Triangles

PETG; check the grooves against your 25 mm blade. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Rim Taper
By Krypto
Complexity
Medium
Workshop Woodworking
0
Rim Taper
MAIN PURPOSE: Read bowl wall thickness at the lathe
Slide the tapered slot onto the rim of a bowl with the lathe stopped: it stops where the gap matches the wall, and the engraved number beside that point reads the thickness, from 12 down to 3 mm, without fetching callipers. Long jaws reach 90 mm down over a lip.
Printing notes
37.6 cm³
Volume
46.6 g
Est. weight
5,072
Triangles

PETG, printed flat. Prints flat as a plate, no supports.

AR view Open in app
Preview of Skewer Gallery
By Krypto
Complexity
Medium
Workshop Finishing & painting
0
Skewer Gallery
MAIN PURPOSE: Dry painted small parts without touching
Thread small painted parts, beads or model pieces onto bamboo skewers and lay the skewers across through the paired holes in the end walls: everything dries hanging in mid-air, touching nothing, the tray below catches drips, and four rods hold dozens of parts.
Printing notes
59.1 cm³
Volume
73.3 g
Est. weight
2,304
Triangles

PLA; uses 250 mm bamboo skewers. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Two-handled spool rewinding crank
By Krypto
Complexity
Medium
Workshop Maker & 3D printing
0
Two-handled spool rewinding crank
MAIN PURPOSE: Rewind filament evenly onto another spool
Push the 52 mm hub into an empty spool, wrap a turn of tape round it if the bore is loose, and wind filament from a tangled, cardboard or refill spool with both hands on the grips: an even, steady wind with no crossed turns, which is what causes tangles and failed prints halfway through.
Printing notes
44.8 cm³
Volume
55.5 g
Est. weight
1,032
Triangles

Print the grips in PETG. Prints flat as a plate, no supports. Stacked parts are fused into one print.

AR view Open in app

SO3D.xyz is free and built by one maker. Help keep it running.

Be one of the first supporters this month.
Support · Buy me a coffeeSee the Hobbyist plan