Showcase

Models Showcase

Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category

All Kitchen Desk & office Workshop Bedroom & bathroom Others
Preview of Good-day drop-zone dish
By Krypto
Complexity
Medium
Others Travel & everyday carry
0
Good-day drop-zone dish
MAIN PURPOSE: Empty your pockets into bays whose floors wish you a good day
A dish for the hall table with four bays: KEYS, WALLET, PHONE and BUDS. When you come home everything goes in and the bays fill up. In the morning, as you take each thing, a word appears in the floor beneath it, and when all four are empty the dish says HAVE A GOOD DAY. If a word is still hidden, you know exactly what you are about to leave behind.
Printing notes
65.3 cm³
Volume
80.9 g
Est. weight
16,476
Triangles

Print in two colours with a filament change after the floor so the message stands out. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Relay-proof key-fob safe
By Krypto
Complexity
Multi-part assembly
Others Travel & everyday carry
0
Relay-proof key-fob safe
MAIN PURPOSE: Block keyless car fobs from relay thieves with a foil-lined box
Keyless car fobs never stop talking, and thieves use a relay to pick up the signal through your front door and unlock the car outside. Line this box and its deep slip-on lid with overlapping foil tape and it becomes a Faraday cage: radio waves cannot get in or out. Drop the fobs in at night and test it by trying the car door with the fob inside. NO SIGNAL is raised on the lid.
Printing notes
91.0 cm³
Volume
112.9 g
Est. weight
10,492
Triangles

Line every inside face of the box, and the inside and skirt of the lid, with overlapping copper or aluminium foil tape. Prints as shown on its floor, no supports. The lid prints as a separate part, top down.

AR view Open in app
Preview of Mend Card
By Krypto
Complexity
Medium
Others Travel & everyday carry
0
Mend Card
MAIN PURPOSE: Carry a needle and thread in the wallet
A credit-card sized mending kit for the wallet: wind black, white and navy thread between the edge notches, weave two needles through the tiny holes and tuck the end of each thread into the side slit. A lost button or split seam on a trip gets fixed in five minutes.
Printing notes
9.0 cm³
Volume
11.1 g
Est. weight
3,620
Triangles

PETG, printed flat. Prints flat as a plate, no supports.

AR view Open in app
Preview of Table Perch
By Krypto
Complexity
Simple
Others Travel & everyday carry
0
Table Perch
MAIN PURPOSE: Hang a bag under a cafe table
Rest the pad on a café or restaurant table so the hook hangs over the edge: the J curls back under the table top, so a handbag or laptop bag hangs off the floor, out of the aisle and against your knees where nobody can lift it. Flat enough for a coat pocket.
Printing notes
40.3 cm³
Volume
49.9 g
Est. weight
584
Triangles

Print it lying on its side (the profile flat on the bed) in PETG. Stick a felt pad under the top.

AR view Open in app
Preview of Haul Hook
By Krypto
Complexity
Simple
Others Travel & everyday carry
0
Haul Hook
MAIN PURPOSE: Carry several shopping bags comfortably
Slip the handles of three or four shopping bags into the hook and carry them all by the 90 mm grip bar: the weight spreads across your whole palm instead of cutting into your fingers, and the J keeps the handles together so the bags stop swinging apart. Lives in the car door pocket.
Printing notes
70.4 cm³
Volume
87.3 g
Est. weight
848
Triangles

Print it lying on its side (the profile flat on the bed) in PETG.

AR view Open in app
Preview of Key Bangle
By Krypto
Complexity
Simple
Others Travel & everyday carry
0
Key Bangle
MAIN PURPOSE: Wear a locker or house key on the wrist
A flexible bracelet for the locker key: slip the open cuff over your wrist and hang the key ring on the tab, so the key stays on you in the pool, at the gym, on a run or on the beach instead of in a pocket you do not have. Print it in TPU so it springs round any wrist.
Printing notes
16.4 cm³
Volume
20.4 g
Est. weight
1,684
Triangles

TPU, printed flat. Prints as shown on its outline, no supports.

AR view Open in app
Preview of Socket Saddle
By Krypto
Complexity
Simple
Others Travel & everyday carry
0
Socket Saddle
MAIN PURPOSE: Hold a charging phone at a low socket
Unplug the phone charger, slip the slot in the back plate over its pins and plug it back in: the charger now holds the saddle to the wall and the phone rests in the pocket below with its cable looped in, instead of on the floor of a hotel room, airport or station with low sockets.
Printing notes
7.2 cm³
Volume
8.9 g
Est. weight
1,660
Triangles

PETG; the plate is only 2.4 mm so the pins still seat fully. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Aisle Clip
By Krypto
Complexity
Simple
Others Travel & everyday carry
0
Aisle Clip
MAIN PURPOSE: Hold a phone or list on a shopping trolley
Snap it onto the handle of a supermarket trolley or basket and stand your phone or paper shopping list in the fork: the list stays in front of you at eye level and both hands stay free for the shelves. Fits handles 28 to 32 mm and phones up to 15 mm thick in a case.
Printing notes
37.0 cm³
Volume
45.9 g
Est. weight
872
Triangles

Print it lying on its side (the profile flat on the bed) in PETG.

AR view Open in app
Preview of Twin Landing
By Krypto
Complexity
Multi-part assembly
Others Travel & everyday carry
0
Twin Landing
MAIN PURPOSE: Pack small valuables, then tray them out
Packs as one closed box for watch, rings, earbuds and cables; in the hotel room lift off the lid, set it down beside the base and you have two landing trays on the nightstand, one for what comes out of your pockets and one for what goes back in tomorrow.
Printing notes
91.5 cm³
Volume
113.4 g
Est. weight
8,572
Triangles

PLA or PETG; line the trays with felt. Prints as shown on its floor, no supports. The lid prints as a separate part, top down.

AR view Open in app
Preview of Tap Sleeve
By Krypto
Complexity
Simple
Others Travel & everyday carry
0
Tap Sleeve
MAIN PURPOSE: Tap a transit card without taking it out
Slide the sleeve onto the shoulder strap of your backpack and push your transit or office pass into the front channel: at the ticket gate or door reader you tap your shoulder, through the 46 mm window, instead of digging through pockets. The card cannot slip out sideways and the strap slides in through the side gap.
Printing notes
29.0 cm³
Volume
35.9 g
Est. weight
1,044
Triangles

PETG, printed standing on end so the channel is clean.

AR view Open in app

SO3D.xyz is free and built by one maker. Help keep it running.

Be one of the first supporters this month.
Support · Buy me a coffeeSee the Hobbyist plan