Showcase
Models Showcase
Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category
MAIN PURPOSE: Deal cards from several decks
A low dealing tray for blackjack, rummy or canasta: up to four shuffled decks lie in it face down, and the dealer slides the top card out through the thumb notch in the low front wall.
Printing notes
61.8 cm³
Volume
76.6 g
Est. weight
1,076
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Stand up game screens and panels
Stand a cardboard game master screen or a folded score sheet up straight: print two, push the panel into the slot, and the wide feet stop it toppling when someone knocks the table.
Printing notes
11.9 cm³
Volume
14.8 g
Est. weight
2,904
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Set insect specimens for display
Set butterflies and moths for a collection: the insect's body sits in the central channel while the wings are pinned flat on foam strips either side until they dry.
Printing notes
94.2 cm³
Volume
116.8 g
Est. weight
1,016
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Field repair for broken tent poles
An emergency splint for a cracked tent pole section up to 11 mm across: slide it over the break and tape both ends, and the tent will stand until you get home.
Printing notes
9.5 cm³
Volume
11.8 g
Est. weight
848
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Wind and fly kite line
An H-shaped winder for kite line: wind the line round the waist in a figure of eight, hold both grips to let the kite out smoothly, and hook the end into the notch when you pack up.
Printing notes
42.6 cm³
Volume
52.8 g
Est. weight
308
Triangles
Prints flat as a plate, no supports.
MAIN PURPOSE: Remove ticks from people and pets
A credit-card-sized tick remover for the wallet or first aid kit: slide the narrow or wide V notch under the tick against the skin and lift it straight out.
Printing notes
8.5 cm³
Volume
10.6 g
Est. weight
188
Triangles
Print flat at 2 mm with fine layers so the notch edges stay crisp.
MAIN PURPOSE: Adjust tent and tarp guy lines
Thread a tent or tarp guy line through the three holes and it holds tension by friction; slide the tensioner along the line to tighten or loosen it without retying any knots.
Printing notes
6.3 cm³
Volume
7.8 g
Est. weight
1,156
Triangles
Prints flat as a plate, no supports.
MAIN PURPOSE: Fix plant stems to canes
Clips a drooping stem or a tomato vine to a cane: the C-shape snaps round both, and it opens again without tools when the plant needs moving.
Printing notes
2.6 cm³
Volume
3.2 g
Est. weight
424
Triangles
Print in PETG or TPU so the clip flexes. Prints flat as a plate, no supports.
MAIN PURPOSE: Contain floating fish food
Floats on the tank surface and keeps flake food in one place, so it doesn't drift into the filter and you can see how much the fish actually eat.
Printing notes
14.5 cm³
Volume
18.0 g
Est. weight
848
Triangles
Print with low (10%) infill so the ring floats. Prints as shown on its floor, no supports.
MAIN PURPOSE: Route airline tube and cables on a tank
Hooks over the rim of an aquarium up to 10 mm thick and holds an airline tube or a heater cable neatly in the corner, so it doesn't float about the tank.
Printing notes
3.6 cm³
Volume
4.5 g
Est. weight
380
Triangles
Prints flat as a plate, no supports.