Showcase

Models Showcase

Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category

All Kitchen Desk & office Workshop Bedroom & bathroom Others
Preview of Index Holster
By Krypto
Complexity
Medium
Others Travel & everyday carry
0
Index Holster
MAIN PURPOSE: Carry a pocket notebook of loose cards and a pen
A pocket holster for 3 x 5 inch index cards, the simplest notebook there is. About fifty cards stand upright with a lowered front so you can read the top one, and a pen sleeve rides along the side. Pull a card, write the idea, put it back at the rear.
Printing notes
11.1 cm³
Volume
13.8 g
Est. weight
4,652
Triangles

Print upright in PETG. Holds 76 x 127 mm cards portrait. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Soap sliver press mould
By Krypto
Complexity
Medium
Others Sustainable living
0
Soap sliver press mould
MAIN PURPOSE: Press leftover soap slivers into a new bar
Chop the last slivers of soap, damp them with a spoonful of hot water and press them hard into this bar mould: the corner holes let the excess water out, and the slivers dry into one solid, usable bar with SOAP pressed into its face.
Printing notes
17.0 cm³
Volume
21.1 g
Est. weight
6,184
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Bottle-to-bottle drain coupler
By Krypto
Complexity
Medium
Others Sustainable living
0
Bottle-to-bottle drain coupler
MAIN PURPOSE: Drain the last drops into a new bottle
Joins two bottles mouth to mouth: the 21 mm spigot plugs into the new bottle, the old one stands upside down in the cup above, and the last shampoo, sauce or washing-up liquid drains across overnight instead of going in the bin.
Printing notes
13.0 cm³
Volume
16.2 g
Est. weight
1,696
Triangles

TPU seals best in the bottle neck. Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of T-shirt yarn cutting guide
By Krypto
Complexity
Medium
Others Sustainable living
0
T-shirt yarn cutting guide
MAIN PURPOSE: Cut old T-shirts into even yarn strips
Fold an old T-shirt flat under the board and run a rotary cutter down the seven slots: the strips come out an even 25 mm wide and stay joined along one edge, so a few diagonal snips turn them into one continuous strand of yarn for crochet rugs and baskets.
Printing notes
121.9 cm³
Volume
151.1 g
Est. weight
18,670
Triangles

Prints flat as a plate, no supports.

AR view Open in app
Preview of Recycled paper-making mould
By Krypto
Complexity
Medium
Others Sustainable living
0
Recycled paper-making mould
MAIN PURPOSE: Make recycled paper sheets from scrap
Blend scrap paper into pulp, tip it into a washing-up bowl and dip this frame: the grid floor carries a piece of fly screen, the walls act as the deckle, and you lift out an even A5 sheet to couch onto a cloth. Stir seeds into the pulp for plantable paper.
Printing notes
93.6 cm³
Volume
116.1 g
Est. weight
4,828
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Cabinet magnet catch block
By Krypto
Complexity
Medium
Others Home hardware & architecture
0
Cabinet magnet catch block
MAIN PURPOSE: Add a magnetic catch to a cabinet door
Screw it inside the cabinet frame, press a 10 x 3 mm neodymium magnet into the centre socket and stick a steel washer on the door: a door that drifts open now closes with a quiet click. Fits where an old roller catch used to be.
Printing notes
1.5 cm³
Volume
1.8 g
Est. weight
468
Triangles

Add one 10 x 3 mm magnet and two small screws. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Furniture anti-tip wall bracket
By Krypto
Complexity
Medium
Others Home hardware & architecture
0
Furniture anti-tip wall bracket
MAIN PURPOSE: Stop tall furniture tipping over
An L-bracket that ties a tall bookcase or chest of drawers to the wall so a climbing child cannot pull it over: one screw into the top of the furniture, one into a wall plug behind it. Use two per piece of furniture.
Printing notes
9.0 cm³
Volume
11.1 g
Est. weight
2,326
Triangles

Print solid (100% infill) in PETG. Prints flat as a plate, no supports.

AR view Open in app
Preview of Downpipe leaf strainer
By Krypto
Complexity
Medium
Others Home hardware & architecture
0
Downpipe leaf strainer
MAIN PURPOSE: Keep leaves out of a gutter downpipe
Push it closed end up into the top of a 68 mm round downpipe where it leaves the gutter: rain pours in through the slotted walls and the holed top, but leaves, moss and lost balls stay up in the gutter to be scooped out, instead of blocking the pipe.
Printing notes
26.6 cm³
Volume
33.0 g
Est. weight
2,636
Triangles

Print standing in ASA or PETG; it is used upside down. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Sash window ventilation stop
By Krypto
Complexity
Medium (set)
Others Home hardware & architecture
0
Sash window ventilation stop
MAIN PURPOSE: Limit how far a sash window opens
Screw one into each side of the sash frame 100 mm above the lower sash: the window still opens far enough for fresh air at night, but stops before a child can climb out or an arm can reach in. Counterbored holes sink the screw heads.
Printing notes
6.7 cm³
Volume
8.3 g
Est. weight
1,676
Triangles

Print two in PETG. Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Drawer bridge shelf
By Krypto
Complexity
Medium
Others Drawer & cabinet organisers
0
Drawer bridge shelf
MAIN PURPOSE: Add a second level inside a deep drawer
Stand it in a deep drawer and the drawer gets two floors: small things live in the tray on top, while flat items such as placemats, chargers or envelopes slide underneath through the open front and back. Lift the bridge out to reach them.
Printing notes
107.2 cm³
Volume
132.9 g
Est. weight
1,076
Triangles

Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app

SO3D.xyz is free and built by one maker. Help keep it running.

Be one of the first supporters this month.
Support · Buy me a coffeeSee the Hobbyist plan