Showcase

Models Showcase

Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category

All Kitchen Desk & office Workshop Bedroom & bathroom Others
Preview of Notepad padding press
By Krypto
Complexity
Simple
Desk & office Paper & bookbinding
0
Notepad padding press
MAIN PURPOSE: Make glued notepads from scrap paper
Jog a stack of A6 sheets into the channel so the top edge stands 10 mm proud, clamp the walls with two bulldog clips and brush on padding glue: when it dries you have a tear-off notepad made from scrap paper.
Printing notes
32.4 cm³
Volume
40.2 g
Est. weight
8,072
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Line-pointer page clip
By Krypto
Complexity
Simple (set)
Desk & office Paper & bookbinding
0
Line-pointer page clip
MAIN PURPOSE: Mark the exact line where you stopped reading
Slip the clip onto the page edge with its point at the line where you stopped: next time you go straight back to the right line, not just the right page. It is thin enough to stay in while the book is closed.
Printing notes
2.1 cm³
Volume
2.6 g
Est. weight
636
Triangles

Print several in PETG. Prints as shown on its outline, no supports.

AR view Open in app
Preview of Book scanning cradle ends
By Krypto
Complexity
Simple (set)
Desk & office Paper & bookbinding
0
Book scanning cradle ends
MAIN PURPOSE: Hold an open book for scanning without strain
Stand the two V-shaped ends under an open book: the 120 degree cradle supports the covers so the spine is not forced flat, and both pages face the camera for scanning or photographing a fragile book. Print two.
Printing notes
74.8 cm³
Volume
92.8 g
Est. weight
716
Triangles

Print two. Prints as shown on its outline, no supports.

AR view Open in app
Preview of Book corner mailing protectors
By Krypto
Complexity
Medium (set)
Desk & office Paper & bookbinding
0
Book corner mailing protectors
MAIN PURPOSE: Protect book corners in the post
Slide a protector onto each corner of a hardback before you wrap it for the post: the corner sits in a sleeve that covers both boards and both edges, so books stop arriving with crushed corners. Fits books up to 28 mm thick. Print four.
Printing notes
15.7 cm³
Volume
19.5 g
Est. weight
84
Triangles

Print four. Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Weighted cable-end anchor
By Krypto
Complexity
Simple
Desk & office Cables & charging
0
Weighted cable-end anchor
MAIN PURPOSE: Stop charging cables sliding off the desk
Snap the charging cables into the three keyhole slots and fill the block with coins: when you unplug the phone, the cable ends stay on the desk instead of sliding off the back and down behind it.
Printing notes
22.2 cm³
Volume
27.5 g
Est. weight
1,912
Triangles

Glue felt or rubber underneath. Prints as shown on its outline, no supports.

AR view Open in app
Preview of RJ45 broken-latch repair clip
By Krypto
Complexity
Simple (set)
Desk & office Cables & charging
0
RJ45 broken-latch repair clip
MAIN PURPOSE: Fix a network cable with a snapped latch
Slide the clip sideways over the body of a network plug whose latch has snapped off: its own springy tongue catches in the socket again, so the cable stays plugged in without crimping a new connector.
Printing notes
1.3 cm³
Volume
1.6 g
Est. weight
528
Triangles

Print in PETG; print a few. Prints as shown on its outline, no supports.

AR view Open in app
Preview of Standing desk cable spine links
By Krypto
Complexity
Medium
Desk & office Cables & charging
0
Standing desk cable spine links
MAIN PURPOSE: Guide cables up a standing desk
Thread a string of links on two 4 mm cords, snap the cables into the C rings and fix the ends to the desk frame and the floor: the spine guides the cables as the desk goes up and down and stops them snagging. Print ten or more.
Printing notes
11.5 cm³
Volume
14.3 g
Est. weight
2,788
Triangles

Print ten or more in PETG. Prints as shown on its outline, no supports.

AR view Open in app
Preview of Monitor arm cable clip
By Krypto
Complexity
Simple (set)
Desk & office Cables & charging
0
Monitor arm cable clip
MAIN PURPOSE: Route cables along a monitor arm
Snap the big C onto a 30 mm monitor arm and the cables into the small one: the cables follow the arm wherever you swing the screen instead of hanging in a loop behind it.
Printing notes
4.0 cm³
Volume
4.9 g
Est. weight
1,248
Triangles

Print three or four in PETG. Prints as shown on its outline, no supports.

AR view Open in app
Preview of Laptop one-push port block
By Krypto
Complexity
Multi-part assembly
Desk & office Cables & charging
0
Laptop one-push port block
MAIN PURPOSE: Dock a laptop with one push
Push the plugs through the wall at your laptop's port spacing (two USB-C and HDMI here), fix them with hot glue and close the lid: docking at the desk becomes one push of the block instead of three fiddly plugs.
Printing notes
9.6 cm³
Volume
11.8 g
Est. weight
8,904
Triangles

Print in PETG; plug metal shells need to be 7 mm long. Prints as shown on its floor, no supports. The lid prints as a separate part, top down.

AR view Open in app
Preview of Webcam privacy clip
By Krypto
Complexity
Simple
Desk & office Office tools
0
Webcam privacy clip
MAIN PURPOSE: Cover a webcam when not in use
A slim clip that slides over the top edge of a laptop lid or monitor up to 7 mm thick, hiding the webcam until you slide it aside for a call.
Printing notes
3.1 cm³
Volume
3.9 g
Est. weight
392
Triangles

Print as it comes (clip outline on the bed), 0.12 mm layers.

AR view Open in app

SO3D.xyz is free and built by one maker. Help keep it running.

Be one of the first supporters this month.
Support · Buy me a coffeeSee the Hobbyist plan