Showcase
Models Showcase
Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category
MAIN PURPOSE: Cap a Bond Brick wall with a phone slot and tray
The coping course for a Bond Brick wall. It caps the top bricks like the coping on a garden wall, closing the cores you are not using, and on top it carries a slot that stands a phone or a stack of cards upright plus a shallow tray in front for clips and a USB stick.
Printing notes
11.0 cm³
Volume
13.6 g
Est. weight
2,020
Triangles
Print in a contrasting colour to the bricks. Prints as shown on its floor, no supports.
MAIN PURPOSE: Store pens by length in a winding stair of cups
A pen tower that climbs like a spiral staircase round its newel. Four cups wind upward round a tall central post, each a step higher than the last, so short pencils sit low at the front and long brushes stand in the newel, and you reach each height by turning the stair.
Printing notes
25.4 cm³
Volume
31.6 g
Est. weight
540
Triangles
Print upright, no supports. Prints as shown on its floor, no supports.
MAIN PURPOSE: Peek a little keeper over the top edge of a book
A bookmark with a guardian on top. The 2 mm strip slides between the pages while a round-headed little keeper peeks over the top of the book, both hands resting on the page edge, eyes cut through. It marks your place and makes a stack of books look inhabited.
Printing notes
8.2 cm³
Volume
10.2 g
Est. weight
680
Triangles
Print flat at 0.2 mm layers; PETG flexes without snapping.
MAIN PURPOSE: Guide desk cables through a lake monster's humps
A loch monster that keeps your cables in line. Its head and neck rise from a 9 mm waterline at one end, three humps arch along the desk and a tail flicks up at the other; thread charging cables through the humps and they stay put. Folklore, cable management and a smile in one 222 mm piece.
Printing notes
69.0 cm³
Volume
85.6 g
Est. weight
1,884
Triangles
Print lying flat in dark green; all strokes come out solid.
MAIN PURPOSE: Hold pens in a cluster of crystal shafts
A crystal cluster that holds pens. Five hexagonal shafts of different heights lean together like a giant quartz point, the tallest 120 mm, each one an open cup for a pen, a brush or a stylus. Print it in translucent PETG and the light runs up the facets.
Printing notes
69.8 cm³
Volume
86.5 g
Est. weight
340
Triangles
Translucent or glitter PETG; print upright with no supports. Prints as shown on its floor, no supports.
MAIN PURPOSE: Tilt split keyboard halves for neutral wrists
Set a wedge under the outer edge of each half of a split keyboard: the 16 degree slope rolls your forearms towards a handshake position, which eases wrist and forearm strain, and the lip at the low end stops the keyboard sliding off. Print two or four.
Printing notes
55.7 cm³
Volume
69.0 g
Est. weight
384
Triangles
Print on its side as it comes; add rubber feet.
MAIN PURPOSE: Use an external keyboard over a laptop
Stand the bridge over a laptop keyboard and put your external keyboard on top: you use the laptop screen at a comfortable distance without the keys being pressed underneath. Two ribs stiffen the 300 mm deck. Print it as shown, then turn it over so the floor becomes the top.
Printing notes
117.2 cm³
Volume
145.3 g
Est. weight
108
Triangles
Print floor-down as shown, then turn it over to use it.
MAIN PURPOSE: Soften a sharp desk edge under the forearms
Clip a few along the front edge of a 25 mm desk: the rounded nose replaces the hard square edge your forearms rest on while typing, which spreads the pressure and keeps the nerve on the underside of the wrist free.
Printing notes
55.1 cm³
Volume
68.3 g
Est. weight
900
Triangles
Print several; PETG or TPU. Prints as shown on its outline, no supports.
MAIN PURPOSE: Keep notifications in view beside the screen
Clamp the jaws on the side edge of a monitor and drop your phone in the pocket: notifications and two-factor codes are in view beside the screen, not face-up on the desk tempting you to pick it up. Fits monitor edges 12 to 14 mm thick.
Printing notes
47.2 cm³
Volume
58.5 g
Est. weight
612
Triangles
Print in PETG. Prints as shown on its outline, no supports.
MAIN PURPOSE: Stop things falling down behind the desk
Hook a pair over the back edge of a desk pushed against the wall: the braced shelf bridges the gap, so pens and chargers no longer drop down behind the desk, and cables still pass behind the upstand. Print two for a long desk.
Printing notes
73.6 cm³
Volume
91.3 g
Est. weight
860
Triangles
Print on its side as it comes; for 25 mm desktops.