Showcase

Models Showcase

Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category

All Kitchen Desk & office Workshop Bedroom & bathroom Others
Preview of Recycled paper-making mould
By Krypto
Complexity
Medium
Others Sustainable living
0
Recycled paper-making mould
MAIN PURPOSE: Make recycled paper sheets from scrap
Blend scrap paper into pulp, tip it into a washing-up bowl and dip this frame: the grid floor carries a piece of fly screen, the walls act as the deckle, and you lift out an even A5 sheet to couch onto a cloth. Stir seeds into the pulp for plantable paper.
Printing notes
93.6 cm³
Volume
116.1 g
Est. weight
4,828
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Shower flow-rate test jug
By Krypto
Complexity
Simple
Others Sustainable living
0
Shower flow-rate test jug
MAIN PURPOSE: Measure shower flow to find water savings
Hold it under the shower for exactly six seconds and read the level: the marks give the flow in litres per minute. Anything over 9 means an aerated shower head would cut hot water, and the energy to heat it, straight away.
Printing notes
26.1 cm³
Volume
32.4 g
Est. weight
8,734
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Tealight cup refill tray
By Krypto
Complexity
Advanced
Others Sustainable living
0
Tealight cup refill tray
MAIN PURPOSE: Refill used tealight cups with leftover wax
Holds eight empty aluminium tealight cups level and upright while you refill them: drop in a wick on its sustainer, pour wax melted from old candle ends, and the cups get a second life instead of going in the bin.
Printing notes
59.5 cm³
Volume
73.8 g
Est. weight
2,348
Triangles

Print in PETG and pour the wax at 70 C or below. Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Reusable bag drying pegs
By Krypto
Complexity
Advanced
Others Sustainable living
0
Reusable bag drying pegs
MAIN PURPOSE: Dry washed reusable bags open
Turn washed zip bags, produce bags and bread bags inside out and slip each over a peg: five staggered pegs of different heights hold them open so air reaches the inside, and they dry in hours instead of staying damp in a drawer.
Printing notes
128.2 cm³
Volume
158.9 g
Est. weight
5,204
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Charger cable strain-relief splint
By Krypto
Complexity
Simple (set)
Others Sustainable living
0
Charger cable strain-relief splint
MAIN PURPOSE: Stop charger cables fraying at the plug
Snap it over a charger or headphone cable where it starts to fray at the plug: the 30 mm sleeve stops the sharp bend that breaks the wires, so a tiny repair keeps the cable out of the e-waste bin for years.
Printing notes
2.8 cm³
Volume
3.4 g
Est. weight
792
Triangles

Print in TPU; print a few. Prints as shown on its outline, no supports.

AR view Open in app
Preview of Door latch hold-open clip
By Krypto
Complexity
Simple
Others Home hardware & architecture
0
Door latch hold-open clip
MAIN PURPOSE: Stop an interior door from latching
Slide the U over the edge of a 40 mm interior door where the latch is: the bolt is held in, so the door closes quietly for a sleeping baby, cannot shut a child or a pet in, and swings open with a nudge while you carry boxes through.
Printing notes
53.3 cm³
Volume
66.1 g
Est. weight
676
Triangles

Print as it comes in PETG or TPU.

AR view Open in app
Preview of Pendant flex shortener
By Krypto
Complexity
Multi-part assembly
Others Home hardware & architecture
0
Pendant flex shortener
MAIN PURPOSE: Shorten a hanging lamp cable neatly
Takes up spare pendant flex neatly instead of a knot: feed the sheathed cable in one side, wind the slack round the inner ring, out of the other side and close the lid. The lamp hangs at exactly the height you want.
Printing notes
36.5 cm³
Volume
45.3 g
Est. weight
6,560
Triangles

Only for sheathed flex, never bare wires. Prints as shown on its floor, no supports. The lid prints as a separate part, top down.

AR view Open in app
Preview of Smart-bulb light switch guard
By Krypto
Complexity
Simple
Others Home hardware & architecture
0
Smart-bulb light switch guard
MAIN PURPOSE: Keep smart bulbs powered at the wall
Screws over a standard 86 mm light switch through the plate's own screw holes and hides the rocker, so nobody switches smart bulbs off at the wall and leaves them unreachable from the app. Two screws out and it is a normal switch again.
Printing notes
16.2 cm³
Volume
20.1 g
Est. weight
6,824
Triangles

Use two longer M3.5 plate screws. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Blind cord safety cleat
By Krypto
Complexity
Simple
Others Home hardware & architecture
0
Blind cord safety cleat
MAIN PURPOSE: Keep blind cords out of children's reach
Fix this T-cleat at least 1.5 m up the window frame and wind the blind cord round its two horns in a figure of eight: the loops stay out of a child's reach, the safety rule for corded blinds and curtains. Drill two 3.5 mm holes through the base for screws.
Printing notes
13.1 cm³
Volume
16.2 g
Est. weight
520
Triangles

Print as it comes (profile on the bed) in PETG.

AR view Open in app
Preview of Cabinet magnet catch block
By Krypto
Complexity
Medium
Others Home hardware & architecture
0
Cabinet magnet catch block
MAIN PURPOSE: Add a magnetic catch to a cabinet door
Screw it inside the cabinet frame, press a 10 x 3 mm neodymium magnet into the centre socket and stick a steel washer on the door: a door that drifts open now closes with a quiet click. Fits where an old roller catch used to be.
Printing notes
1.5 cm³
Volume
1.8 g
Est. weight
468
Triangles

Add one 10 x 3 mm magnet and two small screws. Prints as shown on its floor, no supports.

AR view Open in app

SO3D.xyz is free and built by one maker. Help keep it running.

Be one of the first supporters this month.
Support · Buy me a coffeeSee the Hobbyist plan