Showcase

Models Showcase

Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category

All Kitchen Desk & office Workshop Bedroom & bathroom Others
Preview of First aid box
By Krypto
Complexity
Multi-part assembly
Health & medicine
0
First aid box
A two-bay first aid box with a bar-handled lid and FIRST AID on the front.
Printing notes
409.5 cm³
Volume
507.8 g
Est. weight
8,656
Triangles

Prints as shown on its floor, no supports. The added base's lid prints separately. Stacked parts are fused into one print.

AR view Open in app
Preview of Darning mushroom with gathering neck
By Krypto
Complexity
Advanced
Others Sustainable living
0
Darning mushroom with gathering neck
MAIN PURPOSE: Support fabric while darning holes
Stretch a sock heel or a jumper elbow over the 70 mm face, gather the fabric round the slim neck with a hair tie and weave the darn across a firm, smooth surface. Printed face down, so the darning face comes out glassy and never snags the yarn.
Printing notes
45.3 cm³
Volume
56.2 g
Est. weight
2,200
Triangles

Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Button shank spacer fork
By Krypto
Complexity
Simple (set)
Others Sustainable living
0
Button shank spacer fork
MAIN PURPOSE: Sew buttons on with a strong thread shank
Lay the fork across a coat button between its holes and sew over the two tines; slide it out, wind the thread round the slack and you have a proper thread shank, so buttons on thick fabric stop pulling loose and tearing off.
Printing notes
0.7 cm³
Volume
0.9 g
Est. weight
228
Triangles

Print a few; PETG keeps the tines straight. Prints flat as a plate, no supports.

AR view Open in app
Preview of Soap sliver press mould
By Krypto
Complexity
Medium
Others Sustainable living
0
Soap sliver press mould
MAIN PURPOSE: Press leftover soap slivers into a new bar
Chop the last slivers of soap, damp them with a spoonful of hot water and press them hard into this bar mould: the corner holes let the excess water out, and the slivers dry into one solid, usable bar with SOAP pressed into its face.
Printing notes
17.0 cm³
Volume
21.1 g
Est. weight
6,184
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Toilet cistern displacement box
By Krypto
Complexity
Multi-part assembly
Others Sustainable living
0
Toilet cistern displacement box
MAIN PURPOSE: Save water on every toilet flush
Stand it in the cistern clear of the float and the flush valve, fill it with water or gravel and close the snug lid: every flush now uses about a litre less, the job a brick used to do, but without crumbling grit into the valve.
Printing notes
42.0 cm³
Volume
52.1 g
Est. weight
7,120
Triangles

PETG with solid walls so it stays watertight. Prints as shown on its floor, no supports. The lid prints as a separate part, top down.

AR view Open in app
Preview of Radiator top heat deflector
By Krypto
Complexity
Simple (set)
Others Sustainable living
0
Radiator top heat deflector
MAIN PURPOSE: Direct radiator heat into the room
Sits on top of a 100 mm double-panel radiator, gripping both panels: the shelf and the forward lip turn the rising warm air into the room instead of up behind the curtains or onto a cold window sill. Print several and butt them along the radiator.
Printing notes
173.8 cm³
Volume
215.6 g
Est. weight
744
Triangles

Print as it comes (profile on the bed) in PETG or ASA; radiators reach 70 C.

AR view Open in app
Preview of Bokashi bucket press plate
By Krypto
Complexity
Simple
Others Sustainable living
0
Bokashi bucket press plate
MAIN PURPOSE: Press air out of a bokashi compost bucket
After each layer of scraps and bran, push this plate down hard in the bokashi bucket to squeeze out the air the fermentation hates; six ribs keep the 220 mm plate stiff and give fingers a grip, and it stays on top as the cover layer.
Printing notes
226.2 cm³
Volume
280.5 g
Est. weight
1,528
Triangles

Check the inner diameter of your bucket first. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Bottle-to-bottle drain coupler
By Krypto
Complexity
Medium
Others Sustainable living
0
Bottle-to-bottle drain coupler
MAIN PURPOSE: Drain the last drops into a new bottle
Joins two bottles mouth to mouth: the 21 mm spigot plugs into the new bottle, the old one stands upside down in the cup above, and the last shampoo, sauce or washing-up liquid drains across overnight instead of going in the bin.
Printing notes
13.0 cm³
Volume
16.2 g
Est. weight
1,696
Triangles

TPU seals best in the bottle neck. Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of T-shirt yarn cutting guide
By Krypto
Complexity
Medium
Others Sustainable living
0
T-shirt yarn cutting guide
MAIN PURPOSE: Cut old T-shirts into even yarn strips
Fold an old T-shirt flat under the board and run a rotary cutter down the seven slots: the strips come out an even 25 mm wide and stay joined along one edge, so a few diagonal snips turn them into one continuous strand of yarn for crochet rugs and baskets.
Printing notes
121.9 cm³
Volume
151.1 g
Est. weight
18,670
Triangles

Prints flat as a plate, no supports.

AR view Open in app
Preview of Newspaper seedling pot maker
By Krypto
Complexity
Advanced
Others Sustainable living
0
Newspaper seedling pot maker
MAIN PURPOSE: Roll newspaper into seedling pots
Wrap a strip of newspaper twice round the 50 mm form, fold the overhang under and press the form down hard on the table to crease the base; slide the pot off, fill it with compost and later plant it out paper and all, so seedlings never need plastic pots.
Printing notes
49.1 cm³
Volume
60.9 g
Est. weight
4,452
Triangles

Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app

SO3D.xyz is free and built by one maker. Help keep it running.

Be one of the first supporters this month.
Support · Buy me a coffeeSee the Hobbyist plan