Showcase

Models Showcase

Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category

All Kitchen Desk & office Workshop Bedroom & bathroom Others
Preview of Car cup holder expander
By Krypto
Complexity
Medium
Others Car & bike
0
Car cup holder expander
MAIN PURPOSE: Fit big bottles in small car cup holders
Fits a large water bottle or travel mug into a small car cup holder: the narrow base drops into the holder and the wide cup on top takes the bottle.
Printing notes
78.1 cm³
Volume
96.9 g
Est. weight
1,360
Triangles

Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Car headrest bag hook
By Krypto
Complexity
Simple
Others Car & bike
0
Car headrest bag hook
MAIN PURPOSE: Hang bags behind a car seat
Clips round a front-seat headrest post and holds a handbag or shopping bag behind the seat, off the floor and out of the footwell.
Printing notes
10.4 cm³
Volume
12.9 g
Est. weight
824
Triangles

Print lying flat in PETG or ASA (car interiors get hot).

AR view Open in app
Preview of Handlebar end plugs
By Krypto
Complexity
Medium (set)
Others Car & bike
0
Handlebar end plugs
MAIN PURPOSE: Close open handlebar ends
Push-in end caps for 22 mm bicycle handlebars, replacing lost originals: an open bar end can cut like a punch in a fall.
Printing notes
4.0 cm³
Volume
5.0 g
Est. weight
1,360
Triangles

Print two in PETG or TPU. Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Twist-cap bottle opener
By Krypto
Complexity
Simple
Others Accessibility & daily living
0
Twist-cap bottle opener
MAIN PURPOSE: Open tight bottle caps with less effort
Opens tight plastic bottle caps for anyone with a weak grip: push the tapered jaw over the cap until it wedges, then turn the long handle.
Printing notes
22.1 cm³
Volume
27.4 g
Est. weight
184
Triangles

Prints flat as a plate, no supports.

AR view Open in app
Preview of Can tab lifter
By Krypto
Complexity
Simple
Others Accessibility & daily living
0
Can tab lifter
MAIN PURPOSE: Open ring-pull cans without hurting fingers
A keyring tool that lifts stiff ring-pull tabs on drinks cans and tins without breaking a nail: slip the hooked tip under the tab and lever up.
Printing notes
2.5 cm³
Volume
3.1 g
Est. weight
268
Triangles

Prints flat as a plate, no supports.

AR view Open in app
Preview of Drafting set square
By Krypto
Complexity
Simple
Desk & office Office tools
0
Drafting set square
MAIN PURPOSE: Draw right angles and 45-degree lines
A 45-degree set square for technical drawing, model making and marking out: slide it along a ruler or a T-square for parallel lines, verticals and 45-degree angles.
Printing notes
35.8 cm³
Volume
44.4 g
Est. weight
1,272
Triangles

Prints flat as a plate, no supports.

AR view Open in app
Preview of Bench scraper
By Krypto
Complexity
Medium
Kitchen Baking & sweets
0
Bench scraper
MAIN PURPOSE: Cut and scrape dough
A rigid bench scraper for bread and pastry: cut dough into portions, lift sticky dough off the worktop and scrape the counter clean in one sweep.
Printing notes
53.9 cm³
Volume
66.8 g
Est. weight
1,644
Triangles

Print in food-safe PETG. Prints flat as a plate, no supports.

AR view Open in app
Preview of Fondant smoother
By Krypto
Complexity
Medium
Kitchen Baking & sweets
0
Fondant smoother
MAIN PURPOSE: Smooth fondant on cakes
Smooths rolled fondant over a cake without fingermarks: press the flat paddle down and outwards from the top, then round the sides.
Printing notes
47.5 cm³
Volume
58.9 g
Est. weight
1,132
Triangles

Print in food-safe PETG. Prints flat as a plate, no supports.

AR view Open in app
Preview of Dough thickness guide strips
By Krypto
Complexity
Simple (set)
Kitchen Baking & sweets
0
Dough thickness guide strips
MAIN PURPOSE: Roll dough to an even thickness
Lay one strip each side of the dough and roll the pin along them: the dough comes out exactly 5 mm thick, so cookies and pastry bake evenly.
Printing notes
24.0 cm³
Volume
29.8 g
Est. weight
2,468
Triangles

Print two; change the plate thickness for other sizes. Prints flat as a plate, no supports.

AR view Open in app
Preview of Cake decorating comb
By Krypto
Complexity
Simple
Kitchen Baking & sweets
0
Cake decorating comb
MAIN PURPOSE: Texture buttercream on cakes
Four different edges in one comb, sawtooth, square ridges, round grooves and plain, for patterned sides on buttercream cakes.
Printing notes
31.2 cm³
Volume
38.6 g
Est. weight
792
Triangles

Print in food-safe PETG. Prints flat as a plate, no supports.

AR view Open in app

SO3D.xyz is free and built by one maker. Help keep it running.

Be one of the first supporters this month.
Support · Buy me a coffeeSee the Hobbyist plan