Models Showcase: free 3D-printable organizers

By Krypto

Complexity

Medium

Kitchen Food preparation

0

MAIN PURPOSE: Stone cherries and olives four at a time

Set four cherries or olives stem-up in the seats and push a chopstick down through each: the 12 mm holes let the stone through but not the fruit, and the stones and juice drop into the chamber below. Tip the block back to empty it through the open rear.

Printing notes

22.8 cm³

Volume

28.3 g

Est. weight

1,664

Triangles

Food-safe PETG. Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app

By Krypto

Complexity

Simple

Kitchen Food preparation

0

Hasselback potato cradle

MAIN PURPOSE: Slice potatoes deep without cutting through

Lay a potato in the curved trough and slice across it every few millimetres: the knife lands on the two 10 mm rails before it reaches the bottom, so every cut stops at the same depth and the potato stays in one fanned piece. Works for accordion cucumbers and courgettes too.

Printing notes

31.8 cm³

Volume

39.5 g

Est. weight

1,364

Triangles

Food-safe PETG. Prints as shown on its floor, no supports.

AR view Open in app

By Krypto

Complexity

Simple

Kitchen Serving & table

0

Plate-rim wine glass clip

MAIN PURPOSE: Hold a wine glass on a plate at a buffet

Push the slot onto the rim of a dinner plate and slide the wine glass stem into the keyhole: at a standing buffet you hold the plate and the glass in one hand and keep the other free for the fork. The 6.5 mm snap mouth keeps the stem from slipping out.

Printing notes

7.6 cm³

Volume

9.5 g

Est. weight

312

Triangles

Print in PETG; check the 6.5 mm slot against your plate rim. Prints flat as a plate, no supports.

AR view Open in app

By Krypto

Complexity

Medium

Kitchen Serving & table

0

Steak doneness marker picks

MAIN PURPOSE: Mark how each steak is cooked

Snap the four picks apart and push one into each steak as it comes off the grill: the engraved flags read R, MR, M and WD, so every guest gets the steak cooked the way they asked for, even after resting under foil. Into the dishwasher afterwards.

Printing notes

4.4 cm³

Volume

5.5 g

Est. weight

4,544

Triangles

Food-safe PETG; for resting meat, not on the grill. Prints flat as a plate, no supports.

AR view Open in app

By Krypto

Complexity

Medium

Kitchen Serving & table

0

Soup bowl tilting wedge

MAIN PURPOSE: Tilt a bowl to reach the last spoonfuls

Slide the straight edge under one side of a bowl foot: the step tips the bowl about 8 degrees, so the last of the soup or cereal pools on one side where the spoon can reach it. Helpful for anyone eating one-handed or with an unsteady grip.

Printing notes

12.4 cm³

Volume

15.4 g

Est. weight

392

Triangles

Print in TPU for extra grip. Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app

By Krypto

Complexity

Multi-part assembly

Kitchen Food storage

0

Snack bag pour-spout cap

MAIN PURPOSE: Turn an open bag into a resealable spout

Push the corner of an opened bag of rice, nuts or cereal up through the collar, fold it back over the rim and screw on the cap: the bag now pours from a neat spout and closes airtight instead of being rolled and clipped. Works with paper and foil bags.

Printing notes

11.8 cm³

Volume

14.6 g

Est. weight

2,492

Triangles

Food-safe PETG. Prints as shown on its floor, no supports. The threaded lid and its neck piece print separately; adjust Fit in the Lid tab if it binds.

AR view Open in app

By Krypto

Complexity

Simple

Kitchen Food storage

0

Opened tin can cover

MAIN PURPOSE: Cover an opened tin in the fridge

Snap the cover over the rim of an opened 73 mm tin of pet food, beans or tomato puree before it goes in the fridge: no smell, no cling film, and the flat top lets you stand another tin on it. Rinse and reuse.

Printing notes

13.5 cm³

Volume

16.8 g

Est. weight

680

Triangles

Food-safe PETG or TPU for a tighter snap. Prints as shown on its floor, no supports.

AR view Open in app

By Krypto

Complexity

Simple

Kitchen Food storage

0

Loaf cut-end cap

MAIN PURPOSE: Keep a cut loaf fresh without a bag

Stand a cut sourdough or bloomer cut-face down in the cap on the bread board: the cut end stays soft and the crust stays crisp, which a plastic bag never manages. 150 x 110 mm fits most round and oval loaves.

Printing notes

60.3 cm³

Volume

74.8 g

Est. weight

680

Triangles

Food-safe PETG. Prints as shown on its floor, no supports.

AR view Open in app

By Krypto

Complexity

Medium

Kitchen Food storage

0

Flat-freeze bag former

MAIN PURPOSE: Freeze soup in flat, stackable bricks

Lay a filled one-litre freezer bag of soup or stock in the tray and freeze it: it sets as a flat 20 mm brick that thaws quickly and files upright in the freezer. The open floor lets the cold through and the end notches let you lift the brick out.

Printing notes

78.8 cm³

Volume

97.7 g

Est. weight

14,042

Triangles

PETG stays tough in the freezer. Prints as shown on its floor, no supports.

AR view Open in app

Preview of Espresso puck leveller with depth flange

By Krypto

Complexity

Advanced

Kitchen Coffee & tea

0

Espresso puck leveller with depth flange

MAIN PURPOSE: Level espresso grounds before tamping

Rest the flange on the rim of a 58 mm basket and turn the leveller a few times: the flat face sits 4 mm below the rim and sweeps the grounds into an even, level bed before tamping, which stops channelling. Print the body 1 mm taller for smaller doses.

Printing notes

38.4 cm³

Volume

47.6 g

Est. weight

2,040

Triangles

Food-safe PETG; the flange prints as a small overhang. Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app