Showcase

Models Showcase

Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category

All Kitchen Desk & office Workshop Bedroom & bathroom Others
Preview of 2020 extrusion filament guide clip
By Krypto
Complexity
Simple (set)
Workshop Maker & 3D printing
0
2020 extrusion filament guide clip
MAIN PURPOSE: Guide filament past a printer frame
Snaps into the 6 mm slot of any 2020 aluminium frame and holds a 4 mm PTFE tube 18 mm out from the profile: filament from a top or side spool runs through the tube instead of rubbing a groove into the frame edge and dragging against the extruder.
Printing notes
3.3 cm³
Volume
4.1 g
Est. weight
1,152
Triangles

Print in PETG; print a few along the frame. Prints as shown on its outline, no supports.

AR view Open in app
Preview of Bed-levelling knob quarter-turn caps
By Krypto
Complexity
Simple (set)
Workshop Maker & 3D printing
0
Bed-levelling knob quarter-turn caps
MAIN PURPOSE: Track bed-levelling knob turns
Push a cap over each bed-levelling wheel: the four engraved marks show exactly how far you turned each corner, a quarter turn at a time, so an adjustment can be repeated, halved or undone instead of guessed, and the four corners stop chasing each other.
Printing notes
2.5 cm³
Volume
3.1 g
Est. weight
5,134
Triangles

Print four in TPU so they stretch over knurled 30 mm wheels. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Conductor size and strip-length card
By Krypto
Complexity
Medium
Workshop Trade & professional tools
0
Conductor size and strip-length card
MAIN PURPOSE: Strip wires to length and check conductor size
Push a stripped conductor into the slots along the top: 8, 11, 13 and 18 mm are the strip lengths lever connectors, sockets and switches ask for. The five holes check solid conductor size, 1.5 to 10 mm squared, so the right cable goes on the right breaker.
Printing notes
9.0 cm³
Volume
11.1 g
Est. weight
8,196
Triangles

Print in PETG. Prints flat as a plate, no supports.

AR view Open in app
Preview of Copper pipe square-marking collar
By Krypto
Complexity
Simple
Workshop Trade & professional tools
0
Copper pipe square-marking collar
MAIN PURPOSE: Mark square cuts on copper pipe
Snap the collar onto 15 or 22 mm copper pipe, slide its flat face to your mark and run a pencil round it: the line is square to the pipe, so the cut sits fully home in compression and solder fittings instead of weeping from a slanted end.
Printing notes
17.4 cm³
Volume
21.5 g
Est. weight
1,324
Triangles

Print in PETG. Prints as shown on its outline, no supports.

AR view Open in app
Preview of Notched-trowel wear gauge
By Krypto
Complexity
Medium
Workshop Trade & professional tools
0
Notched-trowel wear gauge
MAIN PURPOSE: Check when a notched trowel is worn out
Hold a notched trowel's teeth against the matching square notch: when a tooth no longer fills the notch, the trowel has worn and spreads too little adhesive under each tile, the usual cause of hollow-sounding and cracking tiles.
Printing notes
13.3 cm³
Volume
16.5 g
Est. weight
6,324
Triangles

Prints flat as a plate, no supports.

AR view Open in app
Preview of Ribbed lightweight plasterer's hawk
By Krypto
Complexity
Advanced
Workshop Trade & professional tools
0
Ribbed lightweight plasterer's hawk
MAIN PURPOSE: Carry plaster or mortar on a light hawk
A 250 mm hawk printed face down: the flat face carries the plaster, a grid of ribs underneath keeps it stiff and light, and the 40 mm handle stands on the centre cross. Easy to wash, and it never warps after a soaking the way plywood hawks do.
Printing notes
265.7 cm³
Volume
329.5 g
Est. weight
1,744
Triangles

Needs a 250 mm bed; print in PETG. Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Survey pole bull's-eye level clip
By Krypto
Complexity
Simple
Workshop Trade & professional tools
0
Survey pole bull's-eye level clip
MAIN PURPOSE: Hold a survey pole plumb
Snaps onto a 25 mm detail or ranging pole and carries a 25 mm bull's-eye vial in its cup: centre the bubble and the pole is plumb over the point, so stakeout and level readings stop drifting by centimetres at the top of a tall pole.
Printing notes
7.6 cm³
Volume
9.4 g
Est. weight
1,336
Triangles

Glue a 25 mm bull's-eye vial into the cup; print in PETG. Prints as shown on its outline, no supports.

AR view Open in app
Preview of Spark plug thread starter
By Krypto
Complexity
Medium
Workshop Trade & professional tools
0
Spark plug thread starter
MAIN PURPOSE: Start spark plugs without cross-threading
Push the soft tube onto the top of a spark plug and use it to lower the plug down a deep plug well and start it by hand: if the thread begins to cross, the tube slips instead of forcing it, so you never strip the thread in an aluminium cylinder head.
Printing notes
3.3 cm³
Volume
4.1 g
Est. weight
6,472
Triangles

Print in TPU. Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Upholstery tucking tool
By Krypto
Complexity
Simple
Workshop Trade & professional tools
0
Upholstery tucking tool
MAIN PURPOSE: Tuck fabric into furniture frames
A flat, tapering blade on a round handle for pushing fabric, leather and wadding into the gap between seat and frame, with a notch in the tip for guiding piping cord: firm enough to push, smooth enough not to snag or scratch show wood.
Printing notes
12.1 cm³
Volume
15.0 g
Est. weight
296
Triangles

Print in PETG or nylon and sand the blade edge smooth. Prints flat as a plate, no supports.

AR view Open in app
Preview of Four-radius fingerboard gauge
By Krypto
Complexity
Medium
Workshop Trade & professional tools
0
Four-radius fingerboard gauge
MAIN PURPOSE: Match string height to the fingerboard radius
Each side of the square is a concave arc: 7.25, 9.5, 12 and 16 inch radius. Sit it on the fingerboard to identify the radius, then under the strings to set the saddle heights to the same curve, so every string has the same action.
Printing notes
13.5 cm³
Volume
16.8 g
Est. weight
8,380
Triangles

Prints flat as a plate, no supports.

AR view Open in app

SO3D.xyz is free and built by one maker. Help keep it running.

Be one of the first supporters this month.
Support · Buy me a coffeeSee the Hobbyist plan