Showcase

Models Showcase

Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category

All Kitchen Desk & office Workshop Bedroom & bathroom Others
Preview of Handlebar end plugs
By Krypto
Complexity
Medium (set)
Others Car & bike
0
Handlebar end plugs
MAIN PURPOSE: Close open handlebar ends
Push-in end caps for 22 mm bicycle handlebars, replacing lost originals: an open bar end can cut like a punch in a fall.
Printing notes
4.0 cm³
Volume
5.0 g
Est. weight
1,360
Triangles

Print two in PETG or TPU. Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Car visor glasses clip
By Krypto
Complexity
Simple
Others Car & bike
0
Car visor glasses clip
MAIN PURPOSE: Keep glasses handy in the car
Clips onto a car sun visor and holds sunglasses or reading glasses by one arm, always within reach and never sliding about on the dashboard.
Printing notes
10.1 cm³
Volume
12.5 g
Est. weight
568
Triangles

Print lying flat in PETG or ASA.

AR view Open in app
Preview of RC car work stand
By Krypto
Complexity
Simple
Workshop Car & bike
0
RC car work stand
MAIN PURPOSE: Hold RC cars with wheels free
A work stand for 1:10 RC cars: set the car on top so its wheels spin free while you tune the motor or change tyres, and carry it to the track by the hand holes. Print it as shown, then turn it over so the floor becomes the top.
Printing notes
48.3 cm³
Volume
59.9 g
Est. weight
2,324
Triangles

Print floor-down as shown, then turn it over to use it. Large holes in the walls may need supports or good bridging.

AR view Open in app
Preview of Windscreen ice scraper
By Krypto
Complexity
Simple
Others Car & bike
0
Windscreen ice scraper
MAIN PURPOSE: Scrape ice off car windscreens
A flat ice scraper with a wide blade for windscreens and a long, narrow handle that keeps your knuckles off the glass; print it in PETG so it stays tough in the cold.
Printing notes
42.4 cm³
Volume
52.6 g
Est. weight
1,444
Triangles

Prints flat as a plate, no supports.

AR view Open in app
Preview of Bike tyre lever
By Krypto
Complexity
Simple (set)
Others Car & bike
0
Bike tyre lever
MAIN PURPOSE: Remove bike tyres from rims
A stiff tyre lever with a spoon tip that slides under the bead and a hooked tail that clips onto a spoke; print two or three in PETG or nylon for the saddle bag.
Printing notes
12.5 cm³
Volume
15.4 g
Est. weight
252
Triangles

Prints flat as a plate, no supports.

AR view Open in app
Preview of Bike torque wrench case
By Krypto
Complexity
Multi-part assembly
Workshop Car & bike
0
Bike torque wrench case
MAIN PURPOSE: Store a compact bicycle torque wrench
A long fitted case for a compact bicycle torque wrench, with a telescoping lid shown beside it.
Printing notes
374.7 cm³
Volume
464.6 g
Est. weight
5,620
Triangles

Prints as shown on its floor, no supports. The lid prints as a separate part, top down.

AR view Open in app
Preview of Automotive blade fuse kit
By Krypto
Complexity
Multi-part assembly
Workshop Car & bike
0
Automotive blade fuse kit
MAIN PURPOSE: Store spare car blade fuses
Twelve small cells for blade fuses by rating, with a flat lid and ring pull for the glovebox.
Printing notes
96.6 cm³
Volume
119.8 g
Est. weight
3,408
Triangles

Prints as shown on its floor, no supports. The lid prints as a separate part, top down.

AR view Open in app
Preview of Car wash bucket grit guard
By Krypto
Complexity
Medium
Workshop Car & bike
0
Car wash bucket grit guard
MAIN PURPOSE: Trap grit below your wash mitt
A honeycomb-perforated disc on feet that sits in the bottom of a wash bucket and keeps grit away from your mitt.
Printing notes
180.4 cm³
Volume
223.7 g
Est. weight
5,516
Triangles

Prints flat as a plate, no supports.

AR view Open in app
Preview of Bike multitool case
By Krypto
Complexity
Multi-part assembly
Others Car & bike
0
Bike multitool case
MAIN PURPOSE: Carry a bike multitool and levers
A fitted case for a folding bike multitool and two tyre levers, with a telescoping lid shown beside it.
Printing notes
175.9 cm³
Volume
218.1 g
Est. weight
5,728
Triangles

Prints as shown on its floor, no supports. The lid prints as a separate part, top down.

AR view Open in app
Preview of Bike puncture repair kit tin
By Krypto
Complexity
Multi-part assembly
Others Car & bike
0
Bike puncture repair kit tin
MAIN PURPOSE: Carry bike puncture repair supplies
Three bays for patches, glue and sandpaper in a tin that fits a saddle bag, with PUNCTURE KIT on the telescoping lid.
Printing notes
44.7 cm³
Volume
55.4 g
Est. weight
8,516
Triangles

Prints as shown on its floor, no supports. The lid prints as a separate part, top down.

AR view Open in app

SO3D.xyz is free and built by one maker. Help keep it running.

Be one of the first supporters this month.
Support · Buy me a coffeeSee the Hobbyist plan