Showcase
Models Showcase
Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category
MAIN PURPOSE: Fix plant canes to a balcony railing
Snaps onto a round balcony handrail up to 43 mm and holds a 12 mm cane upright beside it: two clamps per cane turn a rented balcony into a trellis for tomatoes, beans or sweet peas, with no drilling and no wire round the railing.
Printing notes
32.6 cm³
Volume
40.4 g
Est. weight
2,076
Triangles
Print as it comes in PETG.
MAIN PURPOSE: Keep a dragged hose off garden beds
Push one in at each corner of a bed: the hose slides round the curved head as you pull it along, instead of dragging across the bed and flattening the plants, and the upturned crescent tips stop it riding over the top.
Printing notes
26.4 cm³
Volume
32.8 g
Est. weight
996
Triangles
Print as it comes in ASA or PETG.
MAIN PURPOSE: Spin in the wind as a garden mobile
An S-rotor that turns in the faintest breeze from any direction: hang it floor up from a fishing swivel through the centre hole, and the two offset half-blades work like a Savonius turbine, flashing round as the wind pushes one and slips past the other.
Printing notes
134.8 cm³
Volume
167.1 g
Est. weight
1,700
Triangles
Print as it comes in PETG or ASA.
MAIN PURPOSE: Float a display shelf on tensioned lines
Print two and set one upside down over the other with the hooked arms overlapping: a short line between the hooks and two lines at the outer corners hold the top half floating in mid-air, a tensegrity table for a plant, a speaker or a trophy.
Printing notes
52.0 cm³
Volume
64.5 g
Est. weight
456
Triangles
Print two, profile on the bed; tie with 0.5 mm fishing line in the notches. Prints as shown on its outline, no supports.
MAIN PURPOSE: Lift a shelf board on two compression arches
A riser whose legs follow a true catenary, the curve of a hanging chain turned upside down, so the load runs through it in pure compression like a Gaudi arch. Stand two under the ends of a board to lift a monitor or a row of plants 75 mm higher.
Printing notes
69.0 cm³
Volume
85.6 g
Est. weight
1,300
Triangles
Print two, profile on the bed, in PETG. Prints as shown on its outline, no supports.
MAIN PURPOSE: Time and scent a room with an incense trail
An incense clock shaped as a Hilbert curve, the space-filling path that never crosses itself: fill the 11 mm channel with sand, lay a line of incense powder on it and light one end. The ember walks the 1.4 m path at a steady pace, scenting the room for hours.
Printing notes
102.5 cm³
Volume
127.1 g
Est. weight
5,940
Triangles
Always bed the incense on sand; print in PETG. Prints as shown on its outline, no supports.
MAIN PURPOSE: Pull stiff plugs from wall sockets easily
Stays on the flex for good: the slotted pad sits right behind the plug and the wide T bar gives four fingers something to pull, so a stiff wall socket lets go without pinching the plug or tugging the cable.
Printing notes
11.1 cm³
Volume
13.8 g
Est. weight
352
Triangles
Print flat in PETG.
MAIN PURPOSE: Keep a phone and drink beside the wheelchair
The profile hooks over a 55 mm armrest pad and carries a lipped shelf outboard of the chair: a phone, glasses or a drink stay at hand height without a bag hanging off the frame. A diagonal brace stops it rolling off the pad.
Printing notes
136.6 cm³
Volume
169.4 g
Est. weight
540
Triangles
Print as it comes (profile on the bed) in PETG.
MAIN PURPOSE: Do up buttons and zips with one hand
A fat 30 mm handle fills a weak grip: push the loop through the buttonhole, hook the button and draw it back through. The other end has a small hook for zip pulls, so one tool handles shirt, cardigan and jacket with one hand.
Printing notes
15.8 cm³
Volume
19.6 g
Est. weight
264
Triangles
Print flat in PETG.
MAIN PURPOSE: Pour a full kettle without lifting it
Stand a cordless kettle on the platform against the back rest and push its top: the cradle rolls forward on the curved rocker and pours into the cup in front, then rocks back on its own when you let go. Nobody has to lift a full, hot kettle.
Printing notes
467.5 cm³
Volume
579.7 g
Est. weight
800
Triangles
Print as it comes (profile on the bed) in PETG, 30% infill.