Showcase
Models Showcase
Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category
MAIN PURPOSE: Back a plasterboard hole for filling
Backs a hole up to 70 mm in plasterboard: thread a string through the two centre holes, butter the edges with filler, feed the plate in diagonally and pull it tight behind the board. Tie the string to a pencil across the hole until it sets, then cut it and fill flush.
Printing notes
22.1 cm³
Volume
27.5 g
Est. weight
524
Triangles
Prints flat as a plate, no supports.
MAIN PURPOSE: Use the space around a sink waste pipe
A U-shaped caddy that wraps round the sink waste trap instead of fighting it: the 90 mm slot slides in round the pipe from the front, so the whole cupboard floor holds bottles and sponges, and the caddy lifts out by its two arms for wiping.
Printing notes
415.0 cm³
Volume
514.6 g
Est. weight
760
Triangles
Prints as shown on its outline, no supports.
MAIN PURPOSE: Fit custom dividers in any drawer
Stick a pair of clips facing each other on opposite drawer sides and drop in a strip of 3 mm hardboard, plywood or an old chopping mat: dividers exactly where you want them in any drawer width, and moved in seconds.
Printing notes
6.1 cm³
Volume
7.5 g
Est. weight
972
Triangles
Print in pairs; fix with double-sided tape. Prints as shown on its outline, no supports.
MAIN PURPOSE: Hide valuables under a false drawer floor
Drops into a drawer and hides a shallow compartment: slide a sheet of 3 mm hardboard, cut to size, along the grooves in the side walls and over the lowered front wall, put the socks back on top, and passports or cash lie unseen underneath.
Printing notes
74.6 cm³
Volume
92.5 g
Est. weight
180
Triangles
Add a sheet of 3 mm hardboard cut to size. Prints as shown on its floor, no supports.
MAIN PURPOSE: Hang suspension files in an ordinary drawer
Turns a deep drawer into a filing drawer: hook a clip over each corner of the drawer sides (up to 19 mm thick), lay a 10 mm dowel in the cradles along each side, and standard suspension files hang from the dowels.
Printing notes
12.3 cm³
Volume
15.2 g
Est. weight
1,064
Triangles
Print four, profile on the bed. Prints as shown on its outline, no supports.
MAIN PURPOSE: Stop a drawer from falling out
Screw it loosely to the back of a drawer, standing up: it catches the cabinet's top rail, so the drawer cannot be pulled right out and spill onto the floor. Turn it flat and the drawer comes out for cleaning. Ideal for old drawers without runners.
Printing notes
6.4 cm³
Volume
8.0 g
Est. weight
332
Triangles
Prints flat as a plate, no supports.
MAIN PURPOSE: Use the dummy panel in front of a sink
Screw it to the back of the dummy panel in front of a kitchen sink, add a pair of tip-out hinges, and the dead strip becomes a slim tray for sponges, scourers and a brush. The lower inner wall makes them easy to grab as the panel tilts.
Printing notes
17.5 cm³
Volume
21.7 g
Est. weight
1,320
Triangles
Add a pair of tip-out tray hinges. Prints as shown on its floor, no supports.
MAIN PURPOSE: Root a new plant on the parent branch
Strip a ring of bark from a branch, slide two pods round it through their slots, tape them rim to rim and pack them with damp sphagnum moss: in six to ten weeks roots fill the pod and you cut off a new plant that is already rooted. Works for figs, citrus, rubber plants and roses.
Printing notes
46.9 cm³
Volume
58.2 g
Est. weight
1,084
Triangles
Print two in PETG. Prints as shown on its outline, no supports.
MAIN PURPOSE: Peg strawberry runners down to root
Peg each new plantlet on a strawberry runner onto a small pot of compost with a U-pin, so it roots while the mother plant still feeds it; after three weeks snip the runner and you have a free plant for next year's bed.
Printing notes
2.2 cm³
Volume
2.8 g
Est. weight
180
Triangles
Print a dozen in PETG. Prints flat as a plate, no supports.
MAIN PURPOSE: Hold drip irrigation tubes at each plant
Push the spike into the soil and snap 4 mm micro drip tube into the C clip at the top: each dripper stays pointed at the root zone of its plant instead of wandering, so the irrigation water goes exactly where it is needed.
Printing notes
4.3 cm³
Volume
5.3 g
Est. weight
188
Triangles
Print a batch in PETG or ASA. Prints flat as a plate, no supports.