Showcase

Models Showcase

Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category

All Kitchen Desk & office Workshop Bedroom & bathroom Others
Preview of 80 mm fan guard
By Krypto
Complexity
Medium
Workshop Electronics & robotics
0
80 mm fan guard
MAIN PURPOSE: Guard an 80 mm cooling fan
A honeycomb finger guard for an 80 mm cooling fan in a printer, a PC or an electronics box; it bolts on through the four corner holes with the fan's own screws.
Printing notes
11.3 cm³
Volume
14.0 g
Est. weight
3,660
Triangles

Prints flat as a plate, no supports.

AR view Open in app
Preview of Helping hands base for coolant hose arms
By Krypto
Complexity
Medium
Workshop Electronics & robotics
0
Helping hands base for coolant hose arms
MAIN PURPOSE: Hold circuit boards and wires while soldering
A heavy base for home-made helping hands: push four 1/4-inch segmented coolant hose arms with crocodile clips into the top holes, and fill the base with sand through the bottom hole so it stays put while you solder.
Printing notes
87.5 cm³
Volume
108.5 g
Est. weight
1,840
Triangles

Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Desk cable grommet
By Krypto
Complexity
Medium
Others Home hardware & architecture
0
Desk cable grommet
MAIN PURPOSE: Line a cable hole through a desk
Finishes a 60 mm cable hole drilled through a desk or worktop: the sleeve lines the hole and the flange covers the rough edge, so cables slide through without catching.
Printing notes
16.8 cm³
Volume
20.9 g
Est. weight
1,176
Triangles

Print flange-down; no supports. Prints flat as a plate, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Drop-in vent grille
By Krypto
Complexity
Medium
Others Home hardware & architecture
0
Drop-in vent grille
MAIN PURPOSE: Cover a ventilation opening
A slotted grille for a floor or wall vent opening with a rebate: the skirt drops into the opening and the slotted face lets air through while stopping toys and socks falling in. Print it as shown, then turn it over so the floor becomes the top.
Printing notes
40.2 cm³
Volume
49.8 g
Est. weight
17,736
Triangles

Print floor-down as shown, then turn it over to use it.

AR view Open in app
Preview of Cabinet knob
By Krypto
Complexity
Medium (set)
Others Home hardware & architecture
0
Cabinet knob
MAIN PURPOSE: Replace or add cabinet knobs
A round cabinet or drawer knob: drive a 4 mm screw through the door from the inside into the stem. Print a set in one colour for a quick kitchen refresh. Print it as shown, then turn it over so the floor becomes the top.
Printing notes
6.8 cm³
Volume
8.5 g
Est. weight
1,528
Triangles

Print floor-down as shown, then turn it over to use it.

AR view Open in app
Preview of Wave relief wall tile
By Krypto
Complexity
Medium
Others Geometric & decorative
0
Wave relief wall tile
MAIN PURPOSE: Decorate a wall with modular relief tiles
A square relief tile with a deep wave pattern: hang a set on the wall turning each one by 90 degrees to make your own pattern, and paint them or print them in two colours.
Printing notes
97.0 cm³
Volume
120.3 g
Est. weight
2,216
Triangles

Prints flat as a plate, no supports.

AR view Open in app
Preview of Universal wide grip
By Krypto
Complexity
Medium
Others Accessibility & daily living
0
Universal wide grip
MAIN PURPOSE: Make thin handles easier to hold
Thickens the handle of a pen, a fork or a toothbrush for an easier grip: push the handle through the hole and pad it with tape to fit; the ribbed sides stop it twisting in the hand.
Printing notes
3.4 cm³
Volume
4.2 g
Est. weight
7,320
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Lip balm keychain sleeve
By Krypto
Complexity
Medium
Others Travel & everyday carry
0
Lip balm keychain sleeve
MAIN PURPOSE: Keep lip balm on a keyring
A sleeve that clips a lip balm stick to your keys or bag strap, so it is always to hand and never lost at the bottom of a pocket.
Printing notes
6.4 cm³
Volume
8.0 g
Est. weight
956
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Garden cane connector
By Krypto
Complexity
Medium (set)
Others Garden & plants
0
Garden cane connector
MAIN PURPOSE: Build garden frames from canes
Joins bamboo canes up to 10 mm thick at right angles: push them into the side holes and the top to build frames for netting, climbing beans or a mini greenhouse.
Printing notes
3.1 cm³
Volume
3.9 g
Est. weight
1,832
Triangles

Print several in PETG or ASA. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Eclipse viewer frame
By Krypto
Complexity
Medium
Others Science & education
0
Eclipse viewer frame
MAIN PURPOSE: Hold solar viewing film safely
A sturdy hand-held frame for a sheet of certified solar viewing film (ISO 12312-2): tape the film behind the window, then hold it by the handle to watch an eclipse.
Printing notes
30.7 cm³
Volume
38.1 g
Est. weight
2,304
Triangles

Use only certified solar filter film in the window. Prints flat as a plate, no supports.

AR view Open in app

SO3D.xyz is free and built by one maker. Help keep it running.

Be one of the first supporters this month.
Support · Buy me a coffeeSee the Hobbyist plan