Models Showcase: free 3D-printable organizers

By Krypto

Complexity

Medium

Kitchen Food storage

0

MAIN PURPOSE: Freeze soup in flat, stackable bricks

Lay a filled one-litre freezer bag of soup or stock in the tray and freeze it: it sets as a flat 20 mm brick that thaws quickly and files upright in the freezer. The open floor lets the cold through and the end notches let you lift the brick out.

Printing notes

78.8 cm³

Volume

97.7 g

Est. weight

14,042

Triangles

PETG stays tough in the freezer. Prints as shown on its floor, no supports.

AR view Open in app

By Krypto

Complexity

Medium

Kitchen Coffee & tea

0

Loose-leaf tea portion scoop

MAIN PURPOSE: Measure loose-leaf tea by the cup

Three wells sized for one, two and four cups (5, 10 and 20 ml): dip, level with a finger and tip into the pot, so loose-leaf tea comes out the same strength every time without a set of spoons.

Printing notes

12.7 cm³

Volume

15.7 g

Est. weight

3,490

Triangles

Food-safe PETG. Prints as shown on its floor, no supports.

AR view Open in app

Preview of Inverted AeroPress safety cradle

By Krypto

Complexity

Medium

Kitchen Coffee & tea

0

Inverted AeroPress safety cradle

MAIN PURPOSE: Keep an inverted AeroPress from tipping

Stand an inverted AeroPress with its plunger end in the 66 mm cup while the coffee steeps: the cradle stops the tall, top-heavy press from tipping over and the dish catches any drips, which makes the inverted method safe on a crowded worktop.

Printing notes

58.8 cm³

Volume

72.9 g

Est. weight

1,360

Triangles

Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app

By Krypto

Complexity

Medium (set)

Kitchen Baking & sweets

0

Cake torting knife guides

MAIN PURPOSE: Cut cake layers level and even

Stand a guide on each side of the cake, push a long bread knife through the matching slots (20, 35 or 50 mm up) and turn the cake against the blade: the layers come out perfectly level and even, ready to fill. Print two.

Printing notes

3.5 cm³

Volume

4.3 g

Est. weight

4,956

Triangles

Print two. Prints as shown on its floor, no supports.

AR view Open in app

By Krypto

Complexity

Medium

Desk & office Office tools

0

Large letter size gauge

MAIN PURPOSE: Check whether post goes as a large letter

Push the envelope through the tunnel: if it slides through, it is under 250 mm wide and 25 mm thick and goes at the large letter rate; if it sticks, it is a parcel. Saves a trip to the post office counter.

Printing notes

56.7 cm³

Volume

70.3 g

Est. weight

5,516

Triangles

Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app

By Krypto

Complexity

Medium

Desk & office Office tools

0

Pendulum letter scale

MAIN PURPOSE: Weigh letters without an electronic scale

Hang the scale on a drawing pin through the top hole, clip a letter to the arm with a bulldog clip and read the swing against a plumb thread: up to 100 g, enough for every letter rate. Calibrate the marks once with coins (a 1p weighs 3.56 g).

Printing notes

25.2 cm³

Volume

31.2 g

Est. weight

5,204

Triangles

Print at 100 % infill so the bob has weight. Prints flat as a plate, no supports.

AR view Open in app

By Krypto

Complexity

Medium

Desk & office Paper & bookbinding

0

A-series card scoring board

MAIN PURPOSE: Score A-size cards to fold exactly in half

Push the sheet against the corner stops and run a bone folder down the groove for your size: the four grooves sit at exactly half of A7 to A4, so every card, invitation and booklet folds dead centre, with a crisp crease.

Printing notes

88.9 cm³

Volume

110.3 g

Est. weight

9,660

Triangles

Prints as shown on its floor, no supports.

AR view Open in app

Preview of Book corner mailing protectors

By Krypto

Complexity

Medium (set)

Desk & office Paper & bookbinding

0

Book corner mailing protectors

MAIN PURPOSE: Protect book corners in the post

Slide a protector onto each corner of a hardback before you wrap it for the post: the corner sits in a sleeve that covers both boards and both edges, so books stop arriving with crushed corners. Fits books up to 28 mm thick. Print four.

Printing notes

15.7 cm³

Volume

19.5 g

Est. weight

84

Triangles

Print four. Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app

Preview of Standing desk cable spine links

By Krypto

Complexity

Medium

Desk & office Cables & charging

0

Standing desk cable spine links

MAIN PURPOSE: Guide cables up a standing desk

Thread a string of links on two 4 mm cords, snap the cables into the C rings and fix the ends to the desk frame and the floor: the spine guides the cables as the desk goes up and down and stops them snagging. Print ten or more.

Printing notes

11.5 cm³

Volume

14.3 g

Est. weight

2,788

Triangles

Print ten or more in PETG. Prints as shown on its outline, no supports.

AR view Open in app

By Krypto

Complexity

Medium

Others Tabletop gaming & play

0

Tipping plate balance game

MAIN PURPOSE: Play a stacking and balancing game

A 160 mm plate balanced on a 14 mm post: players take turns placing coins, meeples or dice anywhere on it, and whoever makes the rim touch the table loses. The small foot lets the plate stay level only while the load is centred, so every piece shifts the risk for the next player. Print it as shown, then turn it over so the floor becomes the top.

Printing notes

43.2 cm³

Volume

53.6 g

Est. weight

840

Triangles

Print the plate on the bed, the post upright. Print floor-down as shown, then turn it over to use it.

AR view Open in app