Models Showcase: free 3D-printable organizers

By Krypto

Complexity

Simple (set)

Workshop Woodworking

0

MAIN PURPOSE: Hold pipe clamps steady during a glue-up

Four risers hold 3/4 inch pipe clamps upright and off the bench in a cradle, the same height every time: the clamps stop rolling over, the panel sits level on the bars, and there is room below for squeeze-out and for slipping in the next clamp.

Printing notes

27.8 cm³

Volume

34.4 g

Est. weight

808

Triangles

Print four. Prints as shown on its outline, no supports.

AR view Open in app

Preview of Scalene bevel triangle 15, 30, 45

By Krypto

Complexity

Medium

Workshop Tools & jigs

0

Scalene bevel triangle 15, 30, 45

MAIN PURPOSE: Set exact bevel angles on a saw

A triangle whose corners are 45, 60 and 75 degrees: stand it on the saw table against the tilted blade and its sides set the bevel to 45, 30 or 15 degrees exactly, without trusting the saw's worn tilt scale. It works against a mitre gauge, a drill press table or a sanding disc too.

Printing notes

28.5 cm³

Volume

35.4 g

Est. weight

4,972

Triangles

Print slowly for flat, true faces. Prints as shown on its outline, no supports.

AR view Open in app

Preview of Self-centring dowelling jig for 18 mm board

By Krypto

Complexity

Advanced

Workshop Tools & jigs

0

Self-centring dowelling jig for 18 mm board

MAIN PURPOSE: Drill centred dowel holes in board edges

Drop the jig over the edge of 18 mm board: the two fences straddle it, so the guide holes sit dead centre on the edge, 32 mm apart, and the double guide plates keep an 8 mm bit square. Drill both parts from their face side and the dowels line up every time. Print it as shown, then turn it over so the floor becomes the top.

Printing notes

9.5 cm³

Volume

11.7 g

Est. weight

1,008

Triangles

Print in PETG with 100% infill round the holes. Print floor-down as shown, then turn it over to use it.

AR view Open in app

By Krypto

Complexity

Advanced

Workshop Tools & jigs

0

Hand tap square-start guide

MAIN PURPOSE: Start hand taps square to the work

Clamp or hold the block over a drilled hole and start the tap through the matching guide: two plates 30 mm apart keep an M3, M4, M5 or M6 tap square to the work for the first turns, the moment where most crooked threads and snapped taps happen.

Printing notes

11.5 cm³

Volume

14.3 g

Est. weight

7,836

Triangles

Print in PETG. Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app

By Krypto

Complexity

Medium

Workshop Tools & jigs

0

Threaded rod cutting guide

MAIN PURPOSE: Cut threaded rod square without damaging threads

Run a nut onto M6, M8 or M10 threaded rod, push the rod down through the guide to your mark and saw along the slot between the two plates: the cut comes out square and the thread is supported right up to the blade, and backing the nut off over the end re-forms the first thread.

Printing notes

14.1 cm³

Volume

17.5 g

Est. weight

1,098

Triangles

Print in PETG. Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app

By Krypto

Complexity

Advanced (set)

Workshop Tools & jigs

0

Square-head bench dogs

MAIN PURPOSE: Fence and square work on a dog-hole bench

A 19 mm peg for 20 mm dog holes with a square head whose four flat faces each sit exactly 20 mm from the peg centre: two dogs make a fence parallel to the hole grid, three make a square corner, and the flat faces spread the pressure instead of denting edges like round dogs.

Printing notes

17.0 cm³

Volume

21.1 g

Est. weight

800

Triangles

Print three, with supports under the head. Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app

By Krypto

Complexity

Simple

Workshop Tools & jigs

0

Plasterboard foot lifter

MAIN PURPOSE: Lift wall sheets into place with your foot

Slide the thin toe under a sheet of plasterboard or panelling and step on the back of the lever: the round fulcrum lifts the sheet about 20 mm and holds it tight against the one above while both hands are free to drive the screws.

Printing notes

84.6 cm³

Volume

104.9 g

Est. weight

632

Triangles

Print in PETG, profile on the bed. Prints as shown on its outline, no supports.

AR view Open in app

By Krypto

Complexity

Advanced

Workshop Tools & jigs

0

608 bearing press-in driver

MAIN PURPOSE: Press bearings in without damaging them

Presses a 608 skateboard bearing into a hub or housing by its outer race only: the narrow 1.5 mm rim bears on the race while the 19 mm opening clears the shield and inner race. Tap the solid end with a mallet and the bearing goes in square without brinelling its balls.

Printing notes

19.6 cm³

Volume

24.3 g

Est. weight

1,520

Triangles

Print in PETG with 100% infill. Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app

By Krypto

Complexity

Simple

Workshop Finishing & painting

0

Paint tin rim wiper clip

MAIN PURPOSE: Wipe brushes without filling the lid groove

Clip it onto the rim of a paint tin: you wipe the brush on the arm, which hangs inside the tin, so the excess runs back into the paint instead of filling the lid groove. The lid then seals properly and no dried paint flakes fall in when you open it next time.

Printing notes

14.4 cm³

Volume

17.9 g

Est. weight

956

Triangles

Print in PETG. Prints as shown on its outline, no supports.

AR view Open in app

By Krypto

Complexity

Simple

Workshop Finishing & painting

0

Profile sanding block

MAIN PURPOSE: Sand mouldings without rounding their profiles

One block with three working edges: a half-round bead for coves and flutes, a concave cove for round-overs and dowels, and a sharp 90 degree point for inside corners. Wrap a strip of sandpaper round the edge you need and the profile stays crisp instead of being rounded over by your fingers.

Printing notes

73.2 cm³

Volume

90.8 g

Est. weight

904

Triangles

Prints as shown on its outline, no supports.

AR view Open in app