Showcase

Models Showcase

Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category

All Kitchen Desk & office Workshop Bedroom & bathroom Others
Preview of Lip balm keychain sleeve
By Krypto
Complexity
Medium
Others Travel & everyday carry
0
Lip balm keychain sleeve
MAIN PURPOSE: Keep lip balm on a keyring
A sleeve that clips a lip balm stick to your keys or bag strap, so it is always to hand and never lost at the bottom of a pocket.
Printing notes
6.4 cm³
Volume
8.0 g
Est. weight
956
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Tracker tag key holder
By Krypto
Complexity
Multi-part assembly
Others Travel & everyday carry
0
Tracker tag key holder
MAIN PURPOSE: Attach a tracker tag to keys
A snug round case for a coin-sized Bluetooth tracker tag: the friction lid clicks on over the tag and the tab takes a keyring, so lost keys can be found from your phone.
Printing notes
7.7 cm³
Volume
9.5 g
Est. weight
1,732
Triangles

Prints as shown on its floor, no supports. The friction-fit lid and its neck piece print separately; adjust Fit in the Lid tab if it binds.

AR view Open in app
Preview of Pom-pom maker
By Krypto
Complexity
Simple (set)
Others Crafts & making
0
Pom-pom maker
MAIN PURPOSE: Make yarn pom-poms
Print two of these C-rings and hold them together: wind yarn round and round, cut along the outer edge between the rings, tie the middle tightly and slide the rings off for a full, round pom-pom.
Printing notes
11.7 cm³
Volume
14.5 g
Est. weight
416
Triangles

Print two. Prints flat as a plate, no supports.

AR view Open in app
Preview of Weaving stick shuttle
By Krypto
Complexity
Simple
Others Crafts & making
0
Weaving stick shuttle
MAIN PURPOSE: Carry weft yarn through a loom
A flat stick shuttle for frame and rigid-heddle looms: wind the weft yarn lengthways between the U-notches at each end and pass it through the shed in one smooth slide.
Printing notes
16.7 cm³
Volume
20.7 g
Est. weight
192
Triangles

Prints flat as a plate, no supports.

AR view Open in app
Preview of Embroidery floss bobbin
By Krypto
Complexity
Simple (set)
Others Crafts & making
0
Embroidery floss bobbin
MAIN PURPOSE: Wind and label embroidery thread
Wind a skein of embroidery thread onto the bobbin, tuck the end into the side slit and write the colour number on it; a set keeps a whole floss collection tangle-free.
Printing notes
3.8 cm³
Volume
4.7 g
Est. weight
296
Triangles

Print a set in one go. Prints flat as a plate, no supports.

AR view Open in app
Preview of Candle wick centring bar
By Krypto
Complexity
Simple
Others Crafts & making
0
Candle wick centring bar
MAIN PURPOSE: Keep candle wicks centred while pouring
Lay it across the jar while the wax sets: thread the wick through the centre hole, or two wicks through the outer holes, and they stay straight and centred.
Printing notes
6.4 cm³
Volume
7.9 g
Est. weight
1,156
Triangles

Prints flat as a plate, no supports.

AR view Open in app
Preview of Paper quilling sizing board
By Krypto
Complexity
Advanced
Others Crafts & making
0
Paper quilling sizing board
MAIN PURPOSE: Size paper quilling coils evenly
Drop a loose quilled coil into one of the eight round wells (8 to 36 mm, each size engraved below it) and let it spring open to that size, so every coil in a design comes out the same.
Printing notes
50.3 cm³
Volume
62.4 g
Est. weight
16,500
Triangles

Prints flat as a plate, no supports.

AR view Open in app
Preview of Embossing powder catch tray
By Krypto
Complexity
Simple
Others Crafts & making
0
Embossing powder catch tray
MAIN PURPOSE: Catch and return embossing powder
Pour embossing powder or glitter over a stamped card held above the tray; the excess falls in, and the pouring notch in the low front wall funnels it straight back into the jar.
Printing notes
38.2 cm³
Volume
47.4 g
Est. weight
1,736
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Kumihimo braiding disc
By Krypto
Complexity
Simple
Others Crafts & making
0
Kumihimo braiding disc
MAIN PURPOSE: Braid cord and bracelets
A disc for Japanese kumihimo braiding: hook eight or more threads into the 32 edge slits, rotate the disc and move the threads in turn, and the braid grows down through the centre hole.
Printing notes
83.0 cm³
Volume
102.9 g
Est. weight
912
Triangles

Print in TPU or PETG so the slits grip the threads. Prints flat as a plate, no supports.

AR view Open in app
Preview of Ikebana flower frog
By Krypto
Complexity
Advanced
Others Garden & plants
0
Ikebana flower frog
MAIN PURPOSE: Arrange cut flowers in a shallow bowl
Holds cut stems upright in a shallow bowl or vase: push each stem into a hole in the weighted frog, the way a metal kenzan pin holder would.
Printing notes
43.9 cm³
Volume
54.5 g
Est. weight
2,160
Triangles

Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app

SO3D.xyz is free and built by one maker. Help keep it running.

Be one of the first supporters this month.
Support · Buy me a coffeeSee the Hobbyist plan