Showcase

Models Showcase

Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category

All Kitchen Desk & office Workshop Bedroom & bathroom Others
Preview of Aisle Clip
By Krypto
Complexity
Simple
Others Travel & everyday carry
0
Aisle Clip
MAIN PURPOSE: Hold a phone or list on a shopping trolley
Snap it onto the handle of a supermarket trolley or basket and stand your phone or paper shopping list in the fork: the list stays in front of you at eye level and both hands stay free for the shelves. Fits handles 28 to 32 mm and phones up to 15 mm thick in a case.
Printing notes
37.0 cm³
Volume
45.9 g
Est. weight
872
Triangles

Print it lying on its side (the profile flat on the bed) in PETG.

AR view Open in app
Preview of Twin Landing
By Krypto
Complexity
Multi-part assembly
Others Travel & everyday carry
0
Twin Landing
MAIN PURPOSE: Pack small valuables, then tray them out
Packs as one closed box for watch, rings, earbuds and cables; in the hotel room lift off the lid, set it down beside the base and you have two landing trays on the nightstand, one for what comes out of your pockets and one for what goes back in tomorrow.
Printing notes
91.5 cm³
Volume
113.4 g
Est. weight
8,572
Triangles

PLA or PETG; line the trays with felt. Prints as shown on its floor, no supports. The lid prints as a separate part, top down.

AR view Open in app
Preview of Tap Sleeve
By Krypto
Complexity
Simple
Others Travel & everyday carry
0
Tap Sleeve
MAIN PURPOSE: Tap a transit card without taking it out
Slide the sleeve onto the shoulder strap of your backpack and push your transit or office pass into the front channel: at the ticket gate or door reader you tap your shoulder, through the 46 mm window, instead of digging through pockets. The card cannot slip out sideways and the strap slides in through the side gap.
Printing notes
29.0 cm³
Volume
35.9 g
Est. weight
1,044
Triangles

PETG, printed standing on end so the channel is clean.

AR view Open in app
Preview of Sleeper Ledge
By Krypto
Complexity
Simple
Others Travel & everyday carry
0
Sleeper Ledge
MAIN PURPOSE: Add a bedside shelf to a bunk or berth
Hook it over the guard rail of a bunk, sleeper train berth or hostel bed: the 70 mm shelf sits on the mattress side at pillow height and holds phone, glasses and earplugs within reach in the dark, instead of lost in the sheets. Fits rails up to 26 mm thick.
Printing notes
128.8 cm³
Volume
159.7 g
Est. weight
472
Triangles

Print it lying on its side (the profile flat on the bed) in PETG.

AR view Open in app
Preview of Cuff Handle
By Krypto
Complexity
Simple
Others Travel & everyday carry
0
Cuff Handle
MAIN PURPOSE: Add a handle to a takeaway coffee cup
Slide the split ring up a paper takeaway cup until it wedges on the taper: the hot cup now has a proper handle, so you can carry it without a sleeve or burnt fingers, and it slips off and back into your bag when the cup goes in the recycling. Fits most 12 oz cups.
Printing notes
12.1 cm³
Volume
15.0 g
Est. weight
712
Triangles

PETG, printed flat. Prints flat as a plate, no supports.

AR view Open in app
Preview of Meridiana
By Krypto
Complexity
Medium
Others Science & education
0
Meridiana
MAIN PURPOSE: Mark solar noon and the season with a sun spot
A cathedral meridian line in miniature for a sunny windowsill. Turn the tall wall due south: at solar noon its pinhole throws a spot of sunlight onto the floor rib, and where the spot lands on the engraved marks tells the season, from the high June sun near the wall to the low autumn sun at the back.
Printing notes
35.1 cm³
Volume
43.5 g
Est. weight
12,768
Triangles

Matt light filament shows the spot best. Marks set for about 51 degrees north. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Aroma Stele
By Krypto
Complexity
Multi-part assembly
Others Geometric & decorative
0
Aroma Stele
MAIN PURPOSE: Diffuse essential oil from a hidden felt strip
A slim standing stone for scent without flame or power. Drip essential oil onto a strip of wool felt, drop it inside and close the cap: air drifts through the carved vertical slots on both faces and carries the scent, while the felt stays hidden and the oil never touches the furniture.
Printing notes
22.4 cm³
Volume
27.8 g
Est. weight
12,636
Triangles

PETG resists oils better than PLA. Prints as shown on its floor, no supports. The lid prints as a separate part, top down.

AR view Open in app
Preview of Shoreline Disc
By Krypto
Complexity
Multi-part assembly
Others Music & audio
0
Shoreline Disc
MAIN PURPOSE: Make a soft surf and rain sound by tilting
A tabletop ocean drum. Pour a few spoonfuls of steel BBs or dry rice into the wide shallow drum and close the screw lid: tilt it slowly and the beads roll round the rim like surf on shingle, quicken it for rain. A calming object for the coffee table that is also a real percussion instrument.
Printing notes
353.6 cm³
Volume
438.4 g
Est. weight
6,672
Triangles

Print lid and drum flat; a drop of glue on the thread once filled. Prints as shown on its floor, no supports. The threaded lid and its neck piece print separately; adjust Fit in the Lid tab if it binds.

AR view Open in app
Preview of Ember Cairn
By Krypto
Complexity
Multi-part assembly
Others Geometric & decorative
0
Ember Cairn
MAIN PURPOSE: Keep matches, a striker and spent ends together
A match safe built as a little cairn of stones. Matches stand in the middle stone under a friction cap, the flat crown of the cap takes a strike strip cut from the matchbox, and the small pebble beside the base is the dish for spent matches, so the kit for the fire or candles lives together.
Printing notes
86.2 cm³
Volume
106.9 g
Est. weight
3,992
Triangles

Keep away from children. Glue the strike strip to the cap top. Prints as shown on its floor, no supports. The added base's lid prints separately. Stacked parts are fused into one print.

AR view Open in app
Preview of FitzRoy Tower
By Krypto
Complexity
Medium
Others Science & education
0
FitzRoy Tower
MAIN PURPOSE: House and read a storm glass weather vial
A tower for a 25 mm Victorian storm glass vial. The vial stands inside behind two tall windows, so light passes through and the crystals read clearly, and the side wall carries the old reading key: clear for fair, cloudy for rain, stars for cold and snow.
Printing notes
10.3 cm³
Volume
12.8 g
Est. weight
17,070
Triangles

Measure your vial; set the inner size 2 mm larger. Prints as shown on its floor, no supports. Large holes in the walls may need supports or good bridging.

AR view Open in app

SO3D.xyz is free and built by one maker. Help keep it running.

Be one of the first supporters this month.
Support · Buy me a coffeeSee the Hobbyist plan