Showcase
Models Showcase
Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category
MAIN PURPOSE: Weave small first projects on a frame
A frame loom for first weaving projects: wind the warp thread round the notches at the top and bottom, then weave across the open window to make a mug rug or a small wall hanging.
Printing notes
52.6 cm³
Volume
65.3 g
Est. weight
1,308
Triangles
Prints flat as a plate, no supports.
MAIN PURPOSE: Keep sewing pins on your wrist
The base of a wrist pin cushion: stuff a fabric dome into the cup and thread an elastic or hook-and-loop strap through the two slots underneath, so pins are always at hand while you sew or fit.
Printing notes
13.2 cm³
Volume
16.3 g
Est. weight
1,984
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Display sewing bobbins and hold snips
Sewing machine bobbins stand on edge round a ring channel, so every thread colour shows at a glance; the middle holds a seam ripper and snips.
Printing notes
57.2 cm³
Volume
70.9 g
Est. weight
1,008
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Cover a toggle light switch
A cover plate for a standard North American single toggle switch, with screw holes 83.3 mm apart and a softly rounded edge; print it in a colour that matches the wall. Print it as shown, then turn it over so the floor becomes the top.
Printing notes
15.6 cm³
Volume
19.4 g
Est. weight
1,996
Triangles
Print floor-down as shown, then turn it over to use it.
MAIN PURPOSE: Cradle a spherical smart speaker
A pedestal for a spherical smart speaker about 10 cm across: the rounded inner cove cradles it so it can't roll, and the cable drops through a hole at the back and runs out under the raised feet.
Printing notes
54.2 cm³
Volume
67.2 g
Est. weight
1,228
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Dry and separate folding umbrellas
A slim stand for folding umbrellas by the door: four dividers keep up to four apart so they dry, and the drips collect in the closed base.
Printing notes
361.7 cm³
Volume
448.4 g
Est. weight
1,112
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Scrape ice off car windscreens
A flat ice scraper with a wide blade for windscreens and a long, narrow handle that keeps your knuckles off the glass; print it in PETG so it stays tough in the cold.
Printing notes
42.4 cm³
Volume
52.6 g
Est. weight
1,444
Triangles
Prints flat as a plate, no supports.
MAIN PURPOSE: Remove bike tyres from rims
A stiff tyre lever with a spoon tip that slides under the bead and a hooked tail that clips onto a spoke; print two or three in PETG or nylon for the saddle bag.
Printing notes
12.5 cm³
Volume
15.4 g
Est. weight
252
Triangles
Prints flat as a plate, no supports.
MAIN PURPOSE: Hang a potted plant on the wall
A wall planter with a lower front lip, sized for a 12 cm nursery pot so watering never drips down the wall, hung from two keyholes.
Printing notes
44.7 cm³
Volume
55.4 g
Est. weight
3,384
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Label vegetable and herb plants
A pointed stake for the vegetable bed or herb pot, with the plant name engraved along it.
Printing notes
12.2 cm³
Volume
15.1 g
Est. weight
3,344
Triangles
Prints flat as a plate, no supports.