Showcase

Models Showcase

Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category

All Kitchen Desk & office Workshop Bedroom & bathroom Others
Preview of Mixing bowl tilt ring
By Krypto
Complexity
Simple
Kitchen Kitchen organisers
0
Mixing bowl tilt ring
MAIN PURPOSE: Hold a mixing bowl steady at an angle
Set a mixing bowl in the grippy ring and lean it against the rim at any angle: the bowl stays put while you whisk or fold one-handed, and tilting it gathers the batter where the whisk can get at it.
Printing notes
160.2 cm³
Volume
198.7 g
Est. weight
840
Triangles

Print in TPU. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Flour canister levelling bar
By Krypto
Complexity
Simple
Kitchen Kitchen organisers
0
Flour canister levelling bar
MAIN PURPOSE: Level measuring scoops over the canister
Hook the bar across the mouth of a flour canister or a rolled-down bag (rims about 137 mm apart) and drag each scoop along its straight edge: the measure is level every time and the excess falls back into the canister instead of onto the worktop.
Printing notes
7.1 cm³
Volume
8.8 g
Est. weight
236
Triangles

Food-safe PETG. Prints flat as a plate, no supports.

AR view Open in app
Preview of Fermentation follower disc
By Krypto
Complexity
Medium
Kitchen Food preparation
0
Fermentation follower disc
MAIN PURPOSE: Keep fermenting vegetables submerged
Keeps sauerkraut and kimchi under the brine in a wide-mouth jar: the disc presses the cabbage down, the holes let brine rise above it, and the knob lifts it out without fishing with your fingers.
Printing notes
24.2 cm³
Volume
30.0 g
Est. weight
1,496
Triangles

For food contact, print in a food-safe PETG and wash by hand. Prints flat as a plate, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Fresh pasta nest drying tray
By Krypto
Complexity
Medium
Kitchen Food preparation
0
Fresh pasta nest drying tray
MAIN PURPOSE: Dry fresh pasta nests
Dry six nests of fresh tagliatelle or pappardelle: each nest sits in its own rounded cell and the perforated floor lets air reach underneath, so the pasta dries evenly without sticking.
Printing notes
110.3 cm³
Volume
136.8 g
Est. weight
18,500
Triangles

For food contact, print in a food-safe PETG and wash by hand. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Ravioli cutting grid
By Krypto
Complexity
Advanced
Kitchen Food preparation
0
Ravioli cutting grid
MAIN PURPOSE: Shape and seal ravioli
Cuts eight ravioli at once: lay a sheet of pasta over the fillings, press the grid down so its walls seal and cut the squares, and the vent holes let trapped air out. Print it as shown, then turn it over so the floor becomes the top.
Printing notes
43.6 cm³
Volume
54.1 g
Est. weight
2,352
Triangles

For food contact, print in a food-safe PETG and wash by hand. Print floor-down as shown, then turn it over to use it.

AR view Open in app
Preview of Temaki hand roll stand
By Krypto
Complexity
Medium
Kitchen Serving & table
0
Temaki hand roll stand
MAIN PURPOSE: Serve sushi hand rolls upright
Holds four hand-rolled sushi cones upright at the table so the filling stays inside and the nori stays crisp while everyone rolls their own.
Printing notes
55.2 cm³
Volume
68.4 g
Est. weight
1,676
Triangles

Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Egg yolk separator cup
By Krypto
Complexity
Medium
Kitchen Food preparation
0
Egg yolk separator cup
MAIN PURPOSE: Separate egg yolks from whites
Crack an egg into the cup: the yolk stays in the middle while the white slips through the four slots into the bowl below. The handle hooks over the bowl rim.
Printing notes
24.4 cm³
Volume
30.2 g
Est. weight
4,280
Triangles

For food contact, print in a food-safe PETG and wash by hand. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Soup portion freezer tray
By Krypto
Complexity
Multi-part assembly
Kitchen Food storage
0
Soup portion freezer tray
MAIN PURPOSE: Freeze soup and stock in portions
Freezes soup, stock or sauce in four portion blocks of about half a litre: once frozen, pop the blocks out and bag them, and the tray is free for the next batch. The telescoping lid stops freezer smells.
Printing notes
340.4 cm³
Volume
422.1 g
Est. weight
5,028
Triangles

For food contact, print in a food-safe PETG and wash by hand. Prints as shown on its floor, no supports. The lid prints as a separate part, top down.

AR view Open in app
Preview of Espresso dosing funnel for 58 mm baskets
By Krypto
Complexity
Simple
Kitchen Coffee & tea
0
Espresso dosing funnel for 58 mm baskets
MAIN PURPOSE: Grind into a portafilter without spills
Sits on a 58 mm portafilter while you grind straight into it, so no coffee spills over the rim; lift it off and tamp as usual.
Printing notes
17.8 cm³
Volume
22.0 g
Est. weight
848
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Espresso puck screen and distribution tool dock
By Krypto
Complexity
Medium
Kitchen Coffee & tea
0
Espresso puck screen and distribution tool dock
MAIN PURPOSE: Store espresso puck screen and WDT tool
Parks a 58 mm puck screen flat in the left bay and stands a needle distribution tool upright in the round cup, so both stay clean beside the machine.
Printing notes
57.4 cm³
Volume
71.1 g
Est. weight
1,696
Triangles

Prints as shown on its floor, no supports.

AR view Open in app

SO3D.xyz is free and built by one maker. Help keep it running.

Be one of the first supporters this month.
Support · Buy me a coffeeSee the Hobbyist plan