Showcase

Models Showcase

Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category

All Kitchen Desk & office Workshop Bedroom & bathroom Others
Preview of Split keyboard tenting wedges
By Krypto
Complexity
Simple (set)
Desk & office Desk organisation
0
Split keyboard tenting wedges
MAIN PURPOSE: Tilt split keyboard halves for neutral wrists
Set a wedge under the outer edge of each half of a split keyboard: the 16 degree slope rolls your forearms towards a handshake position, which eases wrist and forearm strain, and the lip at the low end stops the keyboard sliding off. Print two or four.
Printing notes
55.7 cm³
Volume
69.0 g
Est. weight
384
Triangles

Print on its side as it comes; add rubber feet.

AR view Open in app
Preview of Laptop keyboard bridge
By Krypto
Complexity
Simple
Desk & office Desk organisation
0
Laptop keyboard bridge
MAIN PURPOSE: Use an external keyboard over a laptop
Stand the bridge over a laptop keyboard and put your external keyboard on top: you use the laptop screen at a comfortable distance without the keys being pressed underneath. Two ribs stiffen the 300 mm deck. Print it as shown, then turn it over so the floor becomes the top.
Printing notes
117.2 cm³
Volume
145.3 g
Est. weight
108
Triangles

Print floor-down as shown, then turn it over to use it.

AR view Open in app
Preview of Desk-edge forearm guard
By Krypto
Complexity
Simple (set)
Desk & office Desk organisation
0
Desk-edge forearm guard
MAIN PURPOSE: Soften a sharp desk edge under the forearms
Clip a few along the front edge of a 25 mm desk: the rounded nose replaces the hard square edge your forearms rest on while typing, which spreads the pressure and keeps the nerve on the underside of the wrist free.
Printing notes
55.1 cm³
Volume
68.3 g
Est. weight
900
Triangles

Print several; PETG or TPU. Prints as shown on its outline, no supports.

AR view Open in app
Preview of Monitor-side phone holster
By Krypto
Complexity
Simple
Desk & office Desk organisation
0
Monitor-side phone holster
MAIN PURPOSE: Keep notifications in view beside the screen
Clamp the jaws on the side edge of a monitor and drop your phone in the pocket: notifications and two-factor codes are in view beside the screen, not face-up on the desk tempting you to pick it up. Fits monitor edges 12 to 14 mm thick.
Printing notes
47.2 cm³
Volume
58.5 g
Est. weight
612
Triangles

Print in PETG. Prints as shown on its outline, no supports.

AR view Open in app
Preview of Desk-back gap shelf
By Krypto
Complexity
Simple (set)
Desk & office Desk organisation
0
Desk-back gap shelf
MAIN PURPOSE: Stop things falling down behind the desk
Hook a pair over the back edge of a desk pushed against the wall: the braced shelf bridges the gap, so pens and chargers no longer drop down behind the desk, and cables still pass behind the upstand. Print two for a long desk.
Printing notes
73.6 cm³
Volume
91.3 g
Est. weight
860
Triangles

Print on its side as it comes; for 25 mm desktops.

AR view Open in app
Preview of Desk mug lid with spoon slot
By Krypto
Complexity
Simple
Desk & office Desk organisation
0
Desk mug lid with spoon slot
MAIN PURPOSE: Keep a desk drink warm and covered
Drop the lid on your mug at the desk: the tea stays hot, nothing falls in, and a knocked mug spills a lot less near the keyboard. The slot leaves room for a tea bag string or a spoon. Fits mugs up to 88 mm across.
Printing notes
17.3 cm³
Volume
21.5 g
Est. weight
1,340
Triangles

Food-safe PETG. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Rolled-drawing corner weights
By Krypto
Complexity
Multi-part assembly
Desk & office Desk organisation
0
Rolled-drawing corner weights
MAIN PURPOSE: Hold rolled drawings flat on the desk
Fill each triangle with 100 g of coins or steel shot, glue the lid and set one on each corner of a rolled drawing, map or poster: the right angle sits snugly on the corner and the sheet stays flat for reading or tracing.
Printing notes
36.3 cm³
Volume
45.0 g
Est. weight
1,016
Triangles

Print four; glue felt underneath. Prints as shown on its outline, no supports. The lid prints as a separate part, top down.

AR view Open in app
Preview of A5 sticker and stencil drawers
By Krypto
Complexity
Multi-part assembly
Desk & office Desk organisation
0
A5 sticker and stencil drawers
MAIN PURPOSE: Store A5 sheets flat
Three flat drawers that take A5 sticker sheets, stencils and washi samples without bending them, each with a knob and a label slot.
Printing notes
386.0 cm³
Volume
478.7 g
Est. weight
336
Triangles

Prints as shown on its floor, no supports. The 3 drawers print separately from the case.

AR view Open in app
Preview of Sand-filled paperweight
By Krypto
Complexity
Multi-part assembly
Desk & office Desk organisation
0
Sand-filled paperweight
MAIN PURPOSE: Keep loose papers in place
A screw-top paperweight: fill it with sand, rice or a few coins until it feels right, and it holds papers down next to an open window or a desk fan.
Printing notes
45.0 cm³
Volume
55.9 g
Est. weight
4,268
Triangles

Prints as shown on its floor, no supports. The threaded lid and its neck piece print separately; adjust Fit in the Lid tab if it binds.

AR view Open in app
Preview of Event name badge tray
By Krypto
Complexity
Advanced
Desk & office Desk organisation
0
Event name badge tray
MAIN PURPOSE: Sort name badges at events
Lays out name badges alphabetically on the registration table: six lanes marked A-D to U-Z, so guests find their badge in seconds.
Printing notes
196.8 cm³
Volume
244.0 g
Est. weight
5,312
Triangles

Prints as shown on its floor, no supports.

AR view Open in app

SO3D.xyz is free and built by one maker. Help keep it running.

Be one of the first supporters this month.
Support · Buy me a coffeeSee the Hobbyist plan