Showcase

Models Showcase

Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category

All Kitchen Desk & office Workshop Bedroom & bathroom Others
Preview of Poster hanger rail
By Krypto
Complexity
Medium (set)
Desk & office Paper & bookbinding
0
Poster hanger rail
MAIN PURPOSE: Hang posters without frames
Print two and sandwich the top of a poster or a print between them with four small bolts; hang it from the centre hole with a string or a picture hook.
Printing notes
18.8 cm³
Volume
23.3 g
Est. weight
1,492
Triangles

Prints flat as a plate, no supports.

AR view Open in app
Preview of Bookbinding punching cradle
By Krypto
Complexity
Simple
Desk & office Paper & bookbinding
0
Bookbinding punching cradle
MAIN PURPOSE: Punch sewing holes in book signatures
Fold a book signature into the V and poke the sewing holes straight through the slot along the bottom with an awl, so every page lines up for sewing.
Printing notes
439.1 cm³
Volume
544.5 g
Est. weight
592
Triangles

Print as it comes, V outline on the bed; lay it on its side to use it.

AR view Open in app
Preview of Mini display easel
By Krypto
Complexity
Simple
Desk & office Desk organisation
0
Mini display easel
MAIN PURPOSE: Display postcards, photos and small art
A small easel that shows off a postcard, a photo, a tile or a small canvas at a gentle lean; the front ledge stops it sliding off.
Printing notes
66.2 cm³
Volume
82.1 g
Est. weight
380
Triangles

Print as it comes, side outline on the bed; stand it on its base.

AR view Open in app
Preview of Sanding block with grip handle
By Krypto
Complexity
Advanced
Workshop Finishing & painting
0
Sanding block with grip handle
MAIN PURPOSE: Sand flat surfaces by hand
Wrap a strip of sandpaper round the flat-bottomed block and hold it by the handle on top: the pressure spreads evenly, so you sand flat instead of rounding the edges.
Printing notes
44.0 cm³
Volume
54.6 g
Est. weight
1,996
Triangles

Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Shop vacuum hose step adapter
By Krypto
Complexity
Medium
Workshop Tools & jigs
0
Shop vacuum hose step adapter
MAIN PURPOSE: Connect a vacuum hose to a tool dust port
Joins a 58 mm vacuum hose to a tool with a smaller 40 mm dust port: one end fits inside the hose, the other over the port, with a step between them. Wrap tape round a loose joint.
Printing notes
27.7 cm³
Volume
34.3 g
Est. weight
1,696
Triangles

Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Filament spool stand
By Krypto
Complexity
Advanced
Workshop Maker & 3D printing
0
Filament spool stand
MAIN PURPOSE: Feed filament from a spool smoothly
Holds a filament spool next to the printer so it unwinds smoothly: push a 10 mm rod or a broom handle through the spool and rest it in the holes at the top of the two uprights.
Printing notes
47.7 cm³
Volume
59.1 g
Est. weight
3,680
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Gear thumb wheel for M4 bolts
By Krypto
Complexity
Simple
Workshop Tools & jigs
0
Gear thumb wheel for M4 bolts
MAIN PURPOSE: Make hand-tightened bolts for jigs
Turns an M4 bolt into a hand-tightened thumb screw for a printer bed, a jig or a fence: push the bolt through, glue the head into the wheel, and the gear rim gives a firm grip.
Printing notes
3.6 cm³
Volume
4.5 g
Est. weight
1,412
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Pegboard J hook
By Krypto
Complexity
Simple
Workshop Tools & jigs
0
Pegboard J hook
MAIN PURPOSE: Hang tools on pegboard
A J hook for standard pegboard with 1/4-inch holes at 1-inch spacing: the top prong hooks behind the board, the lower one stops it rocking, and the front hook holds a tool.
Printing notes
7.2 cm³
Volume
8.9 g
Est. weight
712
Triangles

Print flat in PETG at 100% infill.

AR view Open in app
Preview of Epoxy mixing palette
By Krypto
Complexity
Medium
Workshop Finishing & painting
0
Epoxy mixing palette
MAIN PURPOSE: Mix small batches of epoxy and resin
Six shallow round wells for mixing small batches of two-part epoxy or resin pigment; cured epoxy flexes out of the smooth, coved wells.
Printing notes
44.1 cm³
Volume
54.6 g
Est. weight
1,700
Triangles

PETG releases cured epoxy well; PLA does not. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Filament end clip
By Krypto
Complexity
Simple
Workshop Maker & 3D printing
0
Filament end clip
MAIN PURPOSE: Stop filament ends unwinding
Clips onto the rim of a filament spool and holds the loose end in its notch, so the filament never unravels into a tangle in storage.
Printing notes
1.5 cm³
Volume
1.9 g
Est. weight
520
Triangles

Prints as shown on its outline, no supports.

AR view Open in app

SO3D.xyz is free and built by one maker. Help keep it running.

Be one of the first supporters this month.
Support · Buy me a coffeeSee the Hobbyist plan