Showcase

Models Showcase

Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category

All Kitchen Desk & office Workshop Bedroom & bathroom Others
Preview of Jointer and router push block
By Krypto
Complexity
Advanced
Workshop Woodworking
0
Jointer and router push block
MAIN PURPOSE: Feed boards safely past a cutter
Keeps your hands well above the cutter when you feed a board over a jointer or across a router table: hold the tall handle and press the grippy base down onto the wood.
Printing notes
70.8 cm³
Volume
87.7 g
Est. weight
2,008
Triangles

Print the base in TPU, or stick rubber grip tape underneath. Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Router circle cutting jig
By Krypto
Complexity
Medium
Workshop Woodworking
0
Router circle cutting jig
MAIN PURPOSE: Cut circles with a router
Cuts perfect circles with a palm router: screw the router base to the wide end, put a nail through one of the pivot holes into the centre of the board, and swing the router round.
Printing notes
67.9 cm³
Volume
84.2 g
Est. weight
1,988
Triangles

Prints flat as a plate, no supports.

AR view Open in app
Preview of Bench dustpan for sawdust
By Krypto
Complexity
Simple
Workshop Woodworking
0
Bench dustpan for sawdust
MAIN PURPOSE: Sweep sawdust off the workbench
A bench dustpan with an open front to sweep into, filleted inner corners and a hanging slot in the back.
Printing notes
112.5 cm³
Volume
139.6 g
Est. weight
1,260
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Joinery biscuit box
By Krypto
Complexity
Multi-part assembly
Workshop Woodworking
0
Joinery biscuit box
MAIN PURPOSE: Sort joining biscuits by size
Three bays for #0, #10 and #20 joining biscuits, with the sizes raised on the telescoping lid.
Printing notes
266.5 cm³
Volume
330.4 g
Est. weight
9,744
Triangles

Prints as shown on its floor, no supports. The lid prints as a separate part, top down.

AR view Open in app
Preview of Bench cookie riser
By Krypto
Complexity
Medium (set)
Workshop Woodworking
0
Bench cookie riser
MAIN PURPOSE: Lift work off the bench
A ribbed riser that lifts work off the bench for routing, sanding and painting, with a honeycomb grip on top; print a set of four. Print it as shown, then turn it over so the floor becomes the top.
Printing notes
31.7 cm³
Volume
39.3 g
Est. weight
5,704
Triangles

Print floor-down as shown, then turn it over to use it.

AR view Open in app
Preview of Pull saw blade guard
By Krypto
Complexity
Simple
Workshop Woodworking
0
Pull saw blade guard
MAIN PURPOSE: Protect a pull saw's teeth
A slim channel that slides over the teeth of a Japanese pull saw, so the blade stays sharp and fingers stay safe in the toolbox.
Printing notes
8.1 cm³
Volume
10.0 g
Est. weight
96
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Corner clamping square
By Krypto
Complexity
Medium
Workshop Woodworking
0
Corner clamping square
MAIN PURPOSE: Clamp box corners at ninety degrees
A rigid 90-degree square for gluing up boxes and frames, with a relief notch in the corner for glue squeeze-out and slots for the clamp jaws.
Printing notes
46.8 cm³
Volume
58.1 g
Est. weight
1,564
Triangles

Prints as shown on its outline, no supports.

AR view Open in app
Preview of Chisel pocket tray
By Krypto
Complexity
Simple
Workshop Woodworking
0
Chisel pocket tray
MAIN PURPOSE: Store a wood chisel in a pocket
A tray with a pocket shaped for a wood chisel.
Printing notes
87.2 cm³
Volume
108.1 g
Est. weight
1,508
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Wood dowel sorter
By Krypto
Complexity
Advanced
Workshop Woodworking
0
Wood dowel sorter
MAIN PURPOSE: Sort wood dowels by diameter in lanes
Six lanes for dowels by diameter.
Printing notes
106.6 cm³
Volume
132.2 g
Est. weight
168
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Carpenter pencil tray
By Krypto
Complexity
Medium
Workshop Woodworking
0
Carpenter pencil tray
MAIN PURPOSE: Hold carpenter pencils, markers and a square
A long rounded tray for carpenter pencils, markers and a square.
Printing notes
32.3 cm³
Volume
40.0 g
Est. weight
1,004
Triangles

Prints as shown on its floor, no supports.

AR view Open in app

SO3D.xyz is free and built by one maker. Help keep it running.

Be one of the first supporters this month.
Support · Buy me a coffeeSee the Hobbyist plan