Showcase

Models Showcase

Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category

All Kitchen Desk & office Workshop Bedroom & bathroom Others
Preview of Aquarium airline and cable clip
By Krypto
Complexity
Simple
Others Pets & aquarium
0
Aquarium airline and cable clip
MAIN PURPOSE: Route airline tube and cables on a tank
Hooks over the rim of an aquarium up to 10 mm thick and holds an airline tube or a heater cable neatly in the corner, so it doesn't float about the tank.
Printing notes
3.6 cm³
Volume
4.5 g
Est. weight
380
Triangles

Prints flat as a plate, no supports.

AR view Open in app
Preview of Egg candling cup
By Krypto
Complexity
Simple
Others Pets & aquarium
0
Egg candling cup
MAIN PURPOSE: Candle eggs during incubation
Check hatching eggs for growth: slip the cup over a small torch or a phone light, rest the egg on the soft rim and look for veins and movement in a dark room.
Printing notes
16.5 cm³
Volume
20.4 g
Est. weight
848
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Hamster tunnel section
By Krypto
Complexity
Simple
Others Pets & aquarium
0
Hamster tunnel section
MAIN PURPOSE: Give small pets tunnels to explore
A tunnel section for hamster and gerbil cages: lay several end to end through the bedding to make burrows, and the hole on top lets air in.
Printing notes
5.3 cm³
Volume
6.5 g
Est. weight
1,836
Triangles

Print lying on its side, or as it comes. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Aquarium fish cave
By Krypto
Complexity
Simple
Others Pets & aquarium
0
Aquarium fish cave
MAIN PURPOSE: Give aquarium fish a place to hide
A hideout for shy fish and shrimp: arched doorways on three sides and a solid roof give them a dark, safe corner of the tank. Print it as shown, then turn it over so the floor becomes the top.
Printing notes
31.9 cm³
Volume
39.5 g
Est. weight
3,020
Triangles

Print in PETG and rinse well before it goes in the tank. Print floor-down as shown, then turn it over to use it. Large holes in the walls may need supports or good bridging.

AR view Open in app
Preview of Hedgehog feeding station
By Krypto
Complexity
Multi-part assembly
Others Pets & aquarium
0
Hedgehog feeding station
MAIN PURPOSE: Feed hedgehogs while excluding cats
A feeding station that lets hedgehogs in but keeps cats away from the food: the 12 cm doorway opens into a corridor, and an inner wall makes visitors turn a corner a cat's paw can't reach round. Weigh the lid down with a brick.
Printing notes
738.6 cm³
Volume
915.9 g
Est. weight
1,156
Triangles

Prints as shown on its floor, no supports. Large holes in the walls may need supports or good bridging. The lid prints as a separate part, top down.

AR view Open in app
Preview of Spill-resistant travel water bowl
By Krypto
Complexity
Medium
Others Pets & aquarium
0
Spill-resistant travel water bowl
MAIN PURPOSE: Carry water for dogs in cars
A dog water bowl for the car or van: the inward-turned top catches the water as it sloshes so it stays in the bowl round corners, and grip feet hold it on the mat.
Printing notes
223.9 cm³
Volume
277.7 g
Est. weight
1,992
Triangles

Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Paw print clay keepsake
By Krypto
Complexity
Simple
Others Pets & aquarium
0
Paw print clay keepsake
MAIN PURPOSE: Capture your pet's paw print
Press your pet's paw into air-dry clay inside this round frame and it becomes a keepsake that hangs on the wall; change the name on the rim before printing.
Printing notes
57.5 cm³
Volume
71.3 g
Est. weight
3,800
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Egg gathering basket
By Krypto
Complexity
Medium
Others Pets & aquarium
0
Egg gathering basket
MAIN PURPOSE: Collect and rinse coop eggs
Collect eggs from the coop and rinse them in the same basket: honeycomb sides let the water drain, the dimpled floor stops eggs rolling, and there is a hand hole at each end.
Printing notes
101.3 cm³
Volume
125.6 g
Est. weight
35,288
Triangles

Prints as shown on its floor, no supports. Large holes in the walls may need supports or good bridging.

AR view Open in app
Preview of Chick feeder trough
By Krypto
Complexity
Advanced
Others Pets & aquarium
0
Chick feeder trough
MAIN PURPOSE: Feed chicks without spilled feed
A feeder that stops chicks scratching their feed everywhere or standing in it: they eat through seven round holes in the lift-off top.
Printing notes
78.8 cm³
Volume
97.8 g
Est. weight
3,492
Triangles

Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Aquarium heater guard
By Krypto
Complexity
Medium
Others Pets & aquarium
0
Aquarium heater guard
MAIN PURPOSE: Shield animals from a hot heater
A slotted sleeve that slides over an aquarium heater so large fish, turtles and axolotls can't rest against the hot glass, while water flows freely through the slots. Print it in PETG.
Printing notes
5.3 cm³
Volume
6.6 g
Est. weight
32,072
Triangles

Prints as shown on its floor, no supports.

AR view Open in app

SO3D.xyz is free and built by one maker. Help keep it running.

Be one of the first supporters this month.
Support · Buy me a coffeeSee the Hobbyist plan