Showcase
Models Showcase
Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category
MAIN PURPOSE: Fit Gridfinity magnets with matching polarity
Stack a column of 6 x 2 mm magnets in the tube: they line up north to south by themselves, so the bottom one always shows the same pole. Press the tube over a bin's magnet pocket, push the stack down with a pencil and slide away, and every bin in the drawer gets the same polarity.
Printing notes
5.1 cm³
Volume
6.3 g
Est. weight
1,980
Triangles
Check the 6 mm bore holds magnets with light friction. Prints as shown on its floor, no supports.
MAIN PURPOSE: Plan Gridfinity grids and bin heights
Lay the long arm in a drawer to count how many 42 mm units fit across it and how much gap is left, then stand the short arm up against the drawer above to see the tallest bin, in 7 mm height units, that will still close. Plan a whole drawer before printing a single bin.
Printing notes
12.4 cm³
Volume
15.4 g
Est. weight
392
Triangles
Prints flat as a plate, no supports.
MAIN PURPOSE: Hang Gridfinity bins on a shelf edge
The back hook drops over the edge of an 18 mm shelf or batten; a bin's back wall slides into the front hook, stacking lip and all. Two hangers turn any Gridfinity bin into a wall or shelf-edge bin and back again, without a dedicated wall plate.
Printing notes
8.3 cm³
Volume
10.3 g
Est. weight
960
Triangles
Print two per bin in PETG. Prints as shown on its outline, no supports.
MAIN PURPOSE: Lock a Gridfinity baseplate tight in a drawer
Drawers are never an exact number of 42 mm units. Push a pair of these tapered wedges between the baseplate and the drawer side, from opposite ends: they close any gap from 4 to 16 mm and lock the grid, so the bins no longer shift when the drawer slams.
Printing notes
12.1 cm³
Volume
15.0 g
Est. weight
644
Triangles
Print in pairs. Prints as shown on its outline, no supports.
MAIN PURPOSE: Store small parts in a Gridfinity bin
A long Gridfinity bin with a scooped front edge for small parts and a label slot.
Printing notes
35.2 cm³
Volume
43.6 g
Est. weight
2,254
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Hold bulky tools in a deep bin
A deep 2x2 Gridfinity bin for bulky tools.
Printing notes
43.8 cm³
Volume
54.3 g
Est. weight
2,304
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Sort three screwdrivers in lanes
A 3x1 Gridfinity tray with three screwdriver lanes.
Printing notes
35.2 cm³
Volume
43.7 g
Est. weight
2,108
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Sort small parts in six cells
A 2x3 Gridfinity sorter with six cells.
Printing notes
73.9 cm³
Volume
91.7 g
Est. weight
2,780
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Organise a drawer with sixteen cells
A sixteen-cell 4x4 Gridfinity bin with its matching baseplate.
Printing notes
218.5 cm³
Volume
270.9 g
Est. weight
10,008
Triangles
Prints as shown on its floor, no supports. The Gridfinity baseplate prints separately.
MAIN PURPOSE: Sort bits in a split bin
A 1x2 Gridfinity bin split in two for bits.
Printing notes
23.9 cm³
Volume
29.7 g
Est. weight
1,876
Triangles
Prints as shown on its floor, no supports.