Showcase

Models Showcase

Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category

All Kitchen Desk & office Workshop Bedroom & bathroom Others
Preview of Wall plug and screw kit
By Krypto
Complexity
Multi-part assembly
Workshop Workshop storage
0
Wall plug and screw kit
MAIN PURPOSE: Match wall plugs with their screws
Four sizes of wall plug, each above the screws that match it, with 5 mm, 6 mm, 8 mm and 10 mm raised on the front and a telescoping lid shown beside it.
Printing notes
160.0 cm³
Volume
198.5 g
Est. weight
20,876
Triangles

Prints as shown on its floor, no supports. The lid prints as a separate part, top down.

AR view Open in app
Preview of Breadboard prototyping tray
By Krypto
Complexity
Simple
Workshop Electronics & robotics
0
Breadboard prototyping tray
MAIN PURPOSE: Hold a breadboard and jumper wires
A tray with a recess for a full-size solderless breadboard, finger notches to lift it out, and a bay beside it for jumper wires.
Printing notes
169.7 cm³
Volume
210.4 g
Est. weight
1,600
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Jigsaw blade case
By Krypto
Complexity
Multi-part assembly
Workshop Workshop storage
0
Jigsaw blade case
MAIN PURPOSE: Sort jigsaw blades by material
Five lanes for T-shank jigsaw blades, with WOOD, FINE, METAL, PLASTIC and CURVE engraved at the end of each lane, and a telescoping lid shown beside it.
Printing notes
104.3 cm³
Volume
129.3 g
Est. weight
16,392
Triangles

Prints as shown on its floor, no supports. The lid prints as a separate part, top down.

AR view Open in app
Preview of Bench cookie riser
By Krypto
Complexity
Medium (set)
Workshop Woodworking
0
Bench cookie riser
MAIN PURPOSE: Lift work off the bench
A ribbed riser that lifts work off the bench for routing, sanding and painting, with a honeycomb grip on top; print a set of four. Print it as shown, then turn it over so the floor becomes the top.
Printing notes
31.7 cm³
Volume
39.3 g
Est. weight
5,704
Triangles

Print floor-down as shown, then turn it over to use it.

AR view Open in app
Preview of Hole saw kit case
By Krypto
Complexity
Multi-part assembly
Workshop Workshop storage
0
Hole saw kit case
MAIN PURPOSE: Store hole saws and arbor
A deep fitted case for five hole saws from 25 to 68 mm and their arbor, with a telescoping lid shown beside it.
Printing notes
897.2 cm³
Volume
1,112.6 g
Est. weight
6,600
Triangles

Prints as shown on its floor, no supports. The lid prints as a separate part, top down.

AR view Open in app
Preview of Right-angle drill guide block
By Krypto
Complexity
Advanced
Workshop Tools & jigs
0
Right-angle drill guide block
MAIN PURPOSE: Keep drill bits square to work
Two plates 34 mm apart with matching 4, 6, 8 and 10 mm holes keep the bit square to the work: hold the block down and drill straight through.
Printing notes
30.2 cm³
Volume
37.4 g
Est. weight
1,496
Triangles

Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Electronics opening tool tray
By Krypto
Complexity
Simple
Workshop Tools & jigs
0
Electronics opening tool tray
MAIN PURPOSE: Store spudgers, picks and pry tools
A shadow tray for four spudgers, picks and pry tools, with a finger channel across the middle.
Printing notes
114.0 cm³
Volume
141.3 g
Est. weight
2,208
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Notched glue spreader
By Krypto
Complexity
Simple
Workshop Finishing & painting
0
Notched glue spreader
MAIN PURPOSE: Spread glue in an even film
A stiff spreader card with fine teeth along one edge for an even film of wood glue or tile adhesive.
Printing notes
9.2 cm³
Volume
11.4 g
Est. weight
636
Triangles

Prints flat as a plate, no supports.

AR view Open in app
Preview of Pull saw blade guard
By Krypto
Complexity
Simple
Workshop Woodworking
0
Pull saw blade guard
MAIN PURPOSE: Protect a pull saw's teeth
A slim channel that slides over the teeth of a Japanese pull saw, so the blade stays sharp and fingers stay safe in the toolbox.
Printing notes
8.1 cm³
Volume
10.0 g
Est. weight
96
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Corner clamping square
By Krypto
Complexity
Medium
Workshop Woodworking
0
Corner clamping square
MAIN PURPOSE: Clamp box corners at ninety degrees
A rigid 90-degree square for gluing up boxes and frames, with a relief notch in the corner for glue squeeze-out and slots for the clamp jaws.
Printing notes
46.8 cm³
Volume
58.1 g
Est. weight
1,564
Triangles

Prints as shown on its outline, no supports.

AR view Open in app

SO3D.xyz is free and built by one maker. Help keep it running.

Be one of the first supporters this month.
Support · Buy me a coffeeSee the Hobbyist plan