Showcase

Models Showcase

Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category

All Kitchen Desk & office Workshop Bedroom & bathroom Others
Preview of Helping hands base for coolant hose arms
By Krypto
Complexity
Medium
Workshop Electronics & robotics
0
Helping hands base for coolant hose arms
MAIN PURPOSE: Hold circuit boards and wires while soldering
A heavy base for home-made helping hands: push four 1/4-inch segmented coolant hose arms with crocodile clips into the top holes, and fill the base with sand through the bottom hole so it stays put while you solder.
Printing notes
87.5 cm³
Volume
108.5 g
Est. weight
1,840
Triangles

Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Mini mitre box
By Krypto
Complexity
Medium
Workshop Woodworking
0
Mini mitre box
MAIN PURPOSE: Cut small strips square and at 45 degrees
Cuts small mouldings, dowels and model-making strips at a clean 90 or 45 degrees: hold the strip in the channel and saw down through the matching slots.
Printing notes
28.1 cm³
Volume
34.8 g
Est. weight
2,724
Triangles

Prints as shown on its floor, no supports. Large holes in the walls may need supports or good bridging.

AR view Open in app
Preview of Fume extractor filter housing
By Krypto
Complexity
Medium
Workshop Electronics & robotics
0
Fume extractor filter housing
MAIN PURPOSE: Pull soldering fumes away from your face
A desk fume extractor body for soldering: a 120 mm fan screws to the back and a carbon filter pad sits in the honeycomb front, pulling smoke away from your face.
Printing notes
26.8 cm³
Volume
33.2 g
Est. weight
5,148
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of 608 bearing pillow block
By Krypto
Complexity
Medium
Workshop Electronics & robotics
0
608 bearing pillow block
MAIN PURPOSE: Mount a 608 bearing in a mechanism
Holds a standard 608 skateboard bearing upright for a home-made spool holder, turntable or small machine: bolt the base down and press the bearing into the upright.
Printing notes
12.7 cm³
Volume
15.8 g
Est. weight
3,318
Triangles

The 22 mm bore is a press fit; sand it lightly if the bearing will not go in. Prints flat as a plate, no supports. Large holes in the walls may need supports or good bridging.

AR view Open in app
Preview of NEMA 17 motor mount plate
By Krypto
Complexity
Medium
Workshop Electronics & robotics
0
NEMA 17 motor mount plate
MAIN PURPOSE: Mount a stepper motor
A flat mounting plate for a NEMA 17 stepper motor: the motor bolts to the four holes round the centre boss opening, and the two slots let you slide the plate to tension a belt.
Printing notes
23.7 cm³
Volume
29.4 g
Est. weight
2,796
Triangles

Check the 31 mm hole spacing against your motor before bolting up. Prints flat as a plate, no supports.

AR view Open in app
Preview of Ultrasonic sensor bracket
By Krypto
Complexity
Medium
Workshop Electronics & robotics
0
Ultrasonic sensor bracket
MAIN PURPOSE: Mount an ultrasonic distance sensor
Holds an HC-SR04 ultrasonic distance sensor facing forward on a robot or a parking aid: the two transducers push through the round holes in the upright.
Printing notes
7.2 cm³
Volume
9.0 g
Est. weight
2,662
Triangles

Prints flat as a plate, no supports. Large holes in the walls may need supports or good bridging.

AR view Open in app
Preview of DIY speaker grille
By Krypto
Complexity
Medium
Workshop Electronics & robotics
0
DIY speaker grille
MAIN PURPOSE: Protect a speaker cone
A perforated front grille for a home-built speaker box: the round holes let the sound through and protect the cone from fingers; screw it on through the four corner holes.
Printing notes
58.9 cm³
Volume
73.0 g
Est. weight
19,422
Triangles

Prints flat as a plate, no supports.

AR view Open in app
Preview of Corner radius marking template
By Krypto
Complexity
Medium
Workshop Woodworking
0
Corner radius marking template
MAIN PURPOSE: Mark rounded corners
Marks four common corner radii, 5, 10, 15 and 25 mm, on boards and panels: line up the template on the corner, trace round it and saw or sand to the line.
Printing notes
28.1 cm³
Volume
34.8 g
Est. weight
7,588
Triangles

Prints flat as a plate, no supports.

AR view Open in app
Preview of Router circle cutting jig
By Krypto
Complexity
Medium
Workshop Woodworking
0
Router circle cutting jig
MAIN PURPOSE: Cut circles with a router
Cuts perfect circles with a palm router: screw the router base to the wide end, put a nail through one of the pivot holes into the centre of the board, and swing the router round.
Printing notes
67.9 cm³
Volume
84.2 g
Est. weight
1,988
Triangles

Prints flat as a plate, no supports.

AR view Open in app
Preview of Model kit sprue and parts tray
By Krypto
Complexity
Medium
Workshop Workshop storage
0
Model kit sprue and parts tray
MAIN PURPOSE: Organise sprues and cut-off model parts
A build tray for plastic model kits: sprue frames stand upright in four slots on the left, and the right side has bays for cut-off parts so nothing tiny goes missing before it is glued.
Printing notes
128.6 cm³
Volume
159.4 g
Est. weight
1,064
Triangles

Prints as shown on its floor, no supports.

AR view Open in app

SO3D.xyz is free and built by one maker. Help keep it running.

Be one of the first supporters this month.
Support · Buy me a coffeeSee the Hobbyist plan