Showcase

Models Showcase

Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category

All Kitchen Desk & office Workshop Bedroom & bathroom Others
Preview of Time capsule with bayonet lid
By Krypto
Complexity
Multi-part assembly
Others Collections & display
0
Time capsule with bayonet lid
MAIN PURPOSE: Bury letters and keepsakes for later
A tall time capsule for letters, photos and small keepsakes, with a twist-lock bayonet lid lettered OPEN IN 2036 round the top; change the year before printing.
Printing notes
230.1 cm³
Volume
285.3 g
Est. weight
9,032
Triangles

Prints as shown on its floor, no supports. The twist-lock lid and its neck piece print separately; adjust Fit in the Lid tab if it binds.

AR view Open in app
Preview of Stethoscope case
By Krypto
Complexity
Multi-part assembly
Others Trade & professional tools
0
Stethoscope case
MAIN PURPOSE: Protect a stethoscope in a bag
A hard case with a fitted recess for a stethoscope, with the chest piece, tubing and ear tips each in their place, so it rides in a bag without tangling or getting crushed.
Printing notes
867.0 cm³
Volume
1,075.1 g
Est. weight
6,100
Triangles

Prints as shown on its floor, no supports. The lid prints as a separate part, top down.

AR view Open in app
Preview of Windscreen ice scraper
By Krypto
Complexity
Simple
Others Car & bike
0
Windscreen ice scraper
MAIN PURPOSE: Scrape ice off car windscreens
A flat ice scraper with a wide blade for windscreens and a long, narrow handle that keeps your knuckles off the glass; print it in PETG so it stays tough in the cold.
Printing notes
42.4 cm³
Volume
52.6 g
Est. weight
1,444
Triangles

Prints flat as a plate, no supports.

AR view Open in app
Preview of Bike tyre lever
By Krypto
Complexity
Simple (set)
Others Car & bike
0
Bike tyre lever
MAIN PURPOSE: Remove bike tyres from rims
A stiff tyre lever with a spoon tip that slides under the bead and a hooked tail that clips onto a spoke; print two or three in PETG or nylon for the saddle bag.
Printing notes
12.5 cm³
Volume
15.4 g
Est. weight
252
Triangles

Prints flat as a plate, no supports.

AR view Open in app
Preview of Self-watering herb pot
By Krypto
Complexity
Medium
Others Garden & plants
0
Self-watering herb pot
MAIN PURPOSE: Water herbs automatically from a reservoir
A herb pot that sits on its own water reservoir: a cotton wick through the centre hole draws water up to the roots, and you top up through the window in the front.
Printing notes
86.9 cm³
Volume
107.8 g
Est. weight
4,448
Triangles

Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Test-tube propagation station
By Krypto
Complexity
Medium
Others Garden & plants
0
Test-tube propagation station
MAIN PURPOSE: Root plant cuttings in water
A rack for five 16 mm glass test tubes: put a cutting in each and watch the roots grow, with the glass doing the water-holding.
Printing notes
45.8 cm³
Volume
56.8 g
Est. weight
3,156
Triangles

Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Bonsai training pot
By Krypto
Complexity
Medium
Others Garden & plants
0
Bonsai training pot
MAIN PURPOSE: Grow and train a bonsai tree
A shallow training pot on feet with two large drain holes and four small holes for wiring the tree in, with chamfered corners and rims.
Printing notes
82.3 cm³
Volume
102.1 g
Est. weight
1,804
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Orchid pot with aeration slots
By Krypto
Complexity
Medium
Others Garden & plants
0
Orchid pot with aeration slots
MAIN PURPOSE: Give orchid roots plenty of air
A square pot slotted on every side and perforated underneath, so orchid roots get the air they need, on small feet.
Printing notes
31.0 cm³
Volume
38.5 g
Est. weight
85,768
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Wall pocket planter
By Krypto
Complexity
Simple
Others Garden & plants
0
Wall pocket planter
MAIN PURPOSE: Hang a potted plant on the wall
A wall planter with a lower front lip, sized for a 12 cm nursery pot so watering never drips down the wall, hung from two keyholes.
Printing notes
44.7 cm³
Volume
55.4 g
Est. weight
3,384
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Air plant cradle
By Krypto
Complexity
Medium
Others Garden & plants
0
Air plant cradle
MAIN PURPOSE: Hold air plants open to light
An open hexagon cradle with a perforated floor, so an air plant gets light and air all round; group a few on a shelf.
Printing notes
28.0 cm³
Volume
34.8 g
Est. weight
5,968
Triangles

Prints as shown on its floor, no supports.

AR view Open in app

SO3D.xyz is free and built by one maker. Help keep it running.

Be one of the first supporters this month.
Support · Buy me a coffeeSee the Hobbyist plan